ZOTYE JNJ7155 Quick Start Manual Download Page 128

Page: 128 / 290

126

Rearview mirror

Exterior rearview mirror

The exterior rearview mirror has the functions shown below:

● Electric adjustment

● * Electric folding

● * Automatic folding

● Defogging and defrosting

Power adjustment of exterior rearview mirror

With the switch ON or the ignition key turned to ON, press the
selector switch of exterior rearview mirror at driver side

①

or the

one at co-driver side

②

, to select the mirror to be adjusted.

Press the button

③

, to alter the mirror angle upwards, downwards,

leftwards and rightwards. After the adjustment, turn off the selector
switch

①

②

Summary of Contents for JNJ7155



































































































































































































































































































Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands

ZOTYE JNJ7155, Quick Start Manual

Search results

Summary of Contents for JNJ7155

Reviews:

Related manuals for JNJ7155

Brands by name

Popular brands