ZOTYE JNJ7155 Quick Start Manual Download Page 118 | Manualshive

Page: 118 / 290

background image

116

Lighting

Delayed off of headlamp (home lighting)

Hazard warning light

When the lighting condition at parking position is poor, the headlamp
prolongs lighting for a certain period to help you with parking.

Turn on home lighting

When the engine is off, turn the light switch to each position one by
one to activate the home lighting: light switch OFF → position light
→ low beam → high beam → low beam → position light → OFF.
The low beam keeps being illuminated for 5 minutes.

When home lighting is activated, the headlamp goes off with 3
minutes delay if any door condition is changed. Such function is valid
for at most 10 times.

Description!

The home lighting shall not be activated when the start switch or
ignition switch has stayed at OFF for over 2 minutes.

The hazard warning light switch is on the central control switch
cluster. When the hazard warning light is turned on, the turn light

flashes and

and

on instrument panel flash.

When the hazard warning light is turned on, the turn light switch
becomes invalid.

Turn on the hazard warning light to attract other drivers’ attention in
case of following circumstances:

«
...
116
117
118
119
120
...
»

Summary of Contents for JNJ7155



































































































































































































































































































Reviews:

No comments

Related manuals for JNJ7155

Brand: AA Products Pages: 6

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 24

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: VEAP SHIELD UNITED Pages: 3

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

Brand: Menabo Pages: 12

Brand: Hudson Pages: 34

Brand: Bestop Pages: 5

Brand: PowerMadd Pages: 3

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: Classic AutoAir Pages: 44

Brand: Grillo Pages: 71

Brand: Scosche Pages: 12

EQ forfour 2018

Brand: SMART Pages: 224

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands