OPEN | CLOSE XS SENSOR
ZSE41
www.getzooz.com
Ÿ
Quick and reliable open/close
alerts sent to your Z-Wave hub
Ÿ
NEW 700 series chip for faster
communication and more
battery life than ever
Ÿ
Extra small for discreet mounting
Ÿ
Waterproof case available for
outdoor installs (sold separately)
Ÿ
Powered by a single coin battery
Ÿ
The latest S2 security and
SmartStart for secure set-up
Ÿ
Supports OTA firmware updates
Ÿ
SE41
Model Number: Z
Ÿ
Z-Wave Frequency: 908.42 MHz
Ÿ
Power: 1 x CR2032 battery
Ÿ
Operating Temperature: 32
°
–
104
°
F
Ÿ
Dimensions: 1.9” x 1” x 0.3”
(magnet: 1.26” x 0.3” x 0.3”)
Ÿ
Range: Up to 130 feet line of sight
Ÿ
Installation and Use: Indoor or
outdoor with waterproof case
(sold separately)
FEATURES
SPECIFICATIONS
1. POWER THE SENSOR
Use a small flat
screwdriver to gently
open the sensor’s cover
and access the battery.
Pull the tab from under the
battery to activate the sensor.
Don’t close the cover just yet.
The LED indicator will start blinking
for around 10 seconds once the
sensor is powered.
The LED indicator doesn’t blink
or light up at all?
Ÿ
Make sure the battery is
inserted correctly per the
positive / negative pole marks.
Ÿ
Try a fresh lithium non-
rechargeable battery.
Ÿ
Click the Z-Wave button 3
times as quickly as possible to
force inclusion/exclusion
mode in case you missed
when it first flashed.
S2
USER MANUAL
Firmware
1
.
10
INSTALLATION
1.
ADD DEVICE to your hub
Initiate inclusion (pairing)
in the
app (or web interface). Not sure
how? [email protected]
If you’re using an S2 hub, it will ask
you to enter the DSK PIN or scan
the QR code printed on the back
cover sticker of the sensor to
complete SmartStart inclusion.
While the hub is looking for new
devices,
click the Z-Wave button
3 times
as quickly as possible.
The LED indicator will start
flashing to confirm inclusion
mode and turn off once inclusion
is completed.
LED INDICATOR
Z-WAVE
BUTTON
Z-WAVE CONTROL
2. ACTIVATE the sensor
3 x CLICK
TO PAIR
SmartThings
Hubitat
Vera
Get more tutorials and helpful tips at
ww.support.getzooz.com
Home Assistant
NEED SOME HELP?
Choose your hub and scan the QR
code with your phone’s camera.
Then click on the link to access the
step-by-step pairing instructions.
TIP!
It’s best to add your sensor from
the area where it will be installed
so the hub can find the best route
to reach it right away.
The
sensor
won’t add to your
system?
Try this:
1. Initiate
EXCLUSION
in your hub
and click the Z-Wave button 3
times
as
quic
kly as possible.
2. Click the Z-Wave button
quicker
when adding it.
3. Bring the
sensor
closer
to your
hub, it may be out of range.
4. Double-check if the device is
powered.
5
. Get troubleshooting tips specific
to your hub at
www.support.getzooz.com
1. Bring the sensor within
direct
range
of your Z-Wave hub.
2
. Put the Z-Wave hub into
exclusion
mode (not sure how to
do that? [email protected])
.
3
. Click
the
Z-Wave button
3 times
as
quickly
as possible
.
4. Your hub will confirm exclusion
and
the
sensor
will disappear
from your controller's device list.
When your network’s primary
controller is missing or otherwise
inoperable, you may need to reset
the device to factory settings
manually. In order to complete the
process, make sure the sensor is
powered, then
click the Z-Wave
button twice and hold it the third
time for 10 seconds.
The LED
indicator will blink continuously.
Immediately a er,
click the Z-
Wave button twice more to
finalize the reset.
The LED
indicator will flash 3 times to
confirm a successful reset.
NOTE: All previously recorded activity and
custom settings will be erased from the
device’s memory.
The sensor’s wake-up interval is set
to 12 hours by default to save
battery life.
Use the Wake Up
Command Class to adjust the
interval.
Click the Z-Wave button 4
times quickly to wake the sensor
up manually.
The LED indicator will
flash twice to confirm the device is
awake. During wake-up, the sensor
turns the Z-Wave radio on for one
minute to receive communication
from the hub. Long wake-up
interval will not affect how o en the
sensor reports to your hub so we
recommend leaving the default
setting to conserve battery.
The XS Sensor supports Group 1
for
Lifeline communication and Group
2 with up
to
5
devices
for basic
on/off control
. This device will send
a Basic Set command to Group 2
when
ever
it detects a change in the
open/close status. It sends an ON
command when OPEN status is
detected and OFF command when
CLOSED status it detected.
Please note that not all Z-Wave
systems give users access to direct
association settings so if you’re
note sure where to find it, please
get in touch with our support and
we’ll be happy to help.
TROUBLESHOOTING
EXCLUSION (REMOVE DEVICE)
FACTORY RESET
WAKE-UP MODE
ASSOCIATION
PAGE 1
PAGE
2
