The Bluetooth PTT (Push To Talk) allows you
to use a compatible BSA adapter with your
two-way radio.
Version 1.0 January 2011
Bluetooth PTT
Model No.: BT-PTT
Made in Taiwan
FCC ID: XTS-BTD-1M3
CE, RoHS Ready
BT-PTT Bluetooth PTT
QUICK START
1. Charge the BT-PTT
2. Pair the BT-PTT with a Bluetooth Adapter and wireless headset.
3. Test and Use.
STEP ONE: Charging the BT-PTT
The BT-PTT has an internal Lithium Ion
rechargeable battery pack which must be
charged prior to operation, and must be
recharged regularly. A fully charged
battery will provide approximately 12
hours (or more) of operation before
needing to be recharged.
To charge the BT-PTT:
* Ensure the BT-PTT is turned off, using
the switch located on the back of the
device.
* Plug the supplied charger into a power
source (USB connector or VAC for wall
power supply if supplied).
* Plug the charger into charge jack on the bottom of the Bluetooth adapter.
You will need to remove the protective rubber cover that is inserted into the
charge jack. (To prevent dust and moisture from damaging your PTT,
always ensure this cover is in place when you are not charging the BT-PTT.)
* The BT-PTT takes approximately 4.5 hours to charge. Actual charge time
will vary depending on several factors including the battery’s charge state,
condition, and age.
Charging Cautions:
- Use only the wall charger supplied by the manufacturer. Do not use
any other charger.
- Do not use a wall charger that appears to be damaged. (Example:
frayed wires, melted plastic, etc.). Contact your distributer to get a new
manufacturer-approved replacement charger.
- Do not tamper with or modify the BT-PTT or charger.
STEP TWO: Pairing the BT-PTT
In order to operate, the BT-PTT must be paired to Bluetooth Adapter
(BSA-93001 series) and Bluetooth headset. To pair these three devices,
follow this procedure:
* The Bluetooth Adapter must be connected to a compatible radio with a
freshly charged battery. Ensure the two-way radio, Bluetooth headset, and
BT-PTT are all powered off.
* Place the adapter in Accessory Pairing mode. To do this, turn the two-way
radio on while holding down the Talk button on the Bluetooth Adapter.
Continue to hold the Talk button down for approximately three seconds.
Release the Talk button when the status LED flashes two times per second.
The Bluetooth Adapter is now in audio accessory pairing mode.
* Activate the pairing mode on your Bluetooth headset by following the
instructions provided by the headset’s manufacturer. Once the wireless
audio accessory and Bluetooth Adapter are paired with each other, the
status
LED on the adapter will show a constant blue light for three seconds.
* Once the headset and adapter have been successfully paired, turn off the
two-way radio and Bluetooth headset and wait at least three seconds.
* Turn on the two-way radio while holding
down the Talk button on the
Bluetooth Adapter. Continue to hold the Talk button down for approximately
three seconds. Release the Talk button when the status LED flashes two
times per second. Then, press the Talk button again. The LED should now
flash three times per second, indicating that the adapter is now in BT-
PTT
Pairing mode.
* Place the BT-PTT in pairing mode by holding down the Push-To-Talk button
while moving the power switch to the On position. The LED will flash twice in
one second.
Once the Bluetooth Adapter and BT-PTT are paired with each
other, the status LED on the adapter will show a constant blue light for three
seconds and the LED on the PTT will show one time per 4 seconds.
* If the Bluetooth Adapter or BT- PTT does not detect a compatible wireless
accessory within 60 seconds of being put
into pairing mode, the devices will exit the
pairing mode and resume normal operation.
*
After pairing is successful, turn off the
BT-PTT and the two-way radio that the
Bluetooth Adapter is attached. Wait at least
three seconds.
STEP THREE: Testing and Using the BT-PTT
After the Bluetooth headset, Bluetooth Adapter and BT-PTT have been
paired with each other you can test and use them together:
* Turn on the two-way radio the Bluetooth Adapter is connected to.
* Turn on the Bluetooth headset. Within a few seconds the LED indicator on
the adapter should show a long flash, indicating the headset and adapter are
connected.
* Turn on the BT-PTT. Within a few seconds the LED indicator on the
adapter should show a long flash, indicating the headset and adapter are
connected. The LED on the PTT should also flash per 4 seconds.
*You will now be able to operate using the wireless accessories. Pressing
the Push-to-Talk button on the BT-PTT will cause the two-way radio to
transmit. Transmit audio will be picked up by the Bluetooth headset.
Received signals will also be heard through the Bluetooth headset’s
earphone.
-----------------------------------------------------------------
Note: You can follow these pairing step if pairing
doesn’t function first time:
1)
Put BT-Headset in pairing mode
2)
Connect BSA-93001 to radio and put the Dongle in pairing mode (2
flash/Sec.)
3)
Paired the BSA-93001 with BT-Headset
4)
Close BT-Headset (important)
5)
Close radio and push BSA-93001 PTT to let BSA-93001 in pairing
mode and push PTT again, Let Dongle in BT-PTT pairing mode.(3
flash/Sec.)
6)
Put BT-PTT in pairing mode. (2 flash/Sec.)
7)
Paired Dongle with BT-PTT.
8)
Power on BT-Headset.(important). BT-
PTT won’t work if BT-Headset is
off.
9)
After BT-Headset link with Dongle then you can use BT-PTT.
BLUETOOTH PTT
USER’S GUIDE
For Compatible Wireless Audio Accessories
