background image

2019-0967 
2019-10-09 

P a g e 

 

 

Installation and Operation Manual 

Zodiac Aquapure Ei Series APURE35C 

by Zodiac Pool Systems, Inc 

2620 Commerce Way 

Vista, California, 92081 USA 

In US: (800) 822-7933 • In Canada (888) 647-4004 

www.ZodiacPoolSystems.com

Swimming pool algicide/bactericide 

Chlorine Generating Device 

For Residential Pools 

DOMESTIC 

REGISTRATION NO. 30232 PEST CONTROL PRODUCTS ACT 

Installation and Operation Manual 

READ THE LABEL AND OPERATION MANUAL BEFORE USING 

KEEP OUT OF REACH OF CHILDREN 

Maximum Overcurrent Protection - 15A 

Use Copper Conductors Only 

Disconnect Power before Opening Service Cover 

For Outdoor or Indoor Use 

Electrical Requirements: 120/240 VAC 50/60 Hz 3 

WIRE, 1.3 AMP 

Maximum Output of Hypochlorous Acid is Equivalent to 420 g 

of Free Available Chlorine Per Day 

4,000 parts per million of salt 

The maximum volume of water that can be treated with 

one unit of APURE35C is 132,000 litres 

(35,000 gallons) (132.0 m

3

For swimming pools, a range of 1-3 ppm of free available 

chlorine must be maintained. 

Controls bacteria and algae in swimming pool water. 
Do not use this device with bromide products. 

BUILDER/INSTALLER: Please leave this manual with the pool owner. 

POOL OWNER: Please save this manual. 

WARNING 

FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool 
equipment by the jurisdiction in which the product will be installed where such local requirements exists. In the event no such 
local requirement exists, the installer or maintainer must be a professional with sufficient experience in pool equipment 
installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this 
product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices 
and instructions may result in property damage, personal injury, or death. Improper installation and/or operation will void 
the warranty. 

Improper installation and/or operation can create unwanted electrical hazard which can cause serious injury, property 
damage, or death. 

Summary of Contents for APURE35C




































Reviews: