14
13
Installing th
e W
ater Line
Installing Filter
INSTALLING FILTER
11
3.Remove the exterior package of the filter, rotate the filter clockwise and press the filter element, and
install the filter element at the joint position of the refrigerator filter until the filter element can not rotate;
4.When the filter sign luminaire in the display panel is on, it prompts to replace the filter element.
The method of removing the filter element is the same as that of removing the dustproof plug;
The filter is recommended to be replaced every half a year
5.
.
1.When the refrigerator is used for the first time, press down the marks on both sides of the filter cover
by hand and open the filter cover downward;
2.Then rotate the dustproof plug anticlockwise and remove the dustproof plug;
2.6 Installing Filter
1. When the refrigerator is used for the first time, press down on the marks on both
sides of the filter cover, by hand, and move the filter cover downward.
2.
11
3.Remove the exterior package of the filter, rotate the filter clockwise and press the filter element, and
install the filter element at the joint position of the refrigerator filter until the filter element can not rotate;
4.When the filter sign luminaire in the display panel is on, it prompts to replace the filter element.
The method of removing the filter element is the same as that of removing the dustproof plug;
The filter is recommended to be replaced every half a year
5.
.
1.When the refrigerator is used for the first time, press down the marks on both sides of the filter cover
by hand and open the filter cover downward;
2.Then rotate the dustproof plug anticlockwise and remove the dustproof plug;
2.6 Installing Filter
Rotate the water filter bypass plug anticlockwise and remove the water filter
bypass plug.
Please save plug in a safe place.
3.
11
3.Remove the exterior package of the filter, rotate the filter clockwise and press the filter element, and
install the filter element at the joint position of the refrigerator filter until the filter element can not rotate;
4.When the filter sign luminaire in the display panel is on, it prompts to replace the filter element.
The method of removing the filter element is the same as that of removing the dustproof plug;
The filter is recommended to be replaced every half a year
5.
.
1.When the refrigerator is used for the first time, press down the marks on both sides of the filter cover
by hand and open the filter cover downward;
2.Then rotate the dustproof plug anticlockwise and remove the dustproof plug;
2.6 Installing Filter
Remove the exterior package of the filter, rotate the filter clockwise, push it into the
filter housing, and install the filter element at the joint position of the refrigerator
filter until the filter element no longer rotates and is secure.
4. When the filter sign light in the display panel turns on, replace the filter element.
5. The method of removing the filter element is the same as that of removing the water
filter bypass plug.
Note
: When installing new filter, drain 2-3 gallons of water to get debris out, or water
may be cloudy and have debris. Only use a ZLINE filter. Otherwise, issues may occur.
INSTALLATION
INSTALLING THE WATER LINE
WARNING
: Risk of electric shock and damage to the appliance. Disconnect
the appliance from the power source before performing any work on the water
connection. Only a qualified technician may connect the appliance to the water
supply in accordance with plumbing and relevant water utility company regulations.
CONNECTING THE WATER LINE TO A POTABLE WATER SOURCE
• If your water line is NOT potable, add an external water filter.
• If you must repair or disassemble the water line, cut off the plastic tubing to make
sure you get a snug, leak-free connection.
Connect the appliance to a drinking water line only:
• Minimum pressure: 0.17 MPa (1.72 bar, 24.95 PSI)
• Maximum pressure: 0.82 MPa (8.25 bar, 119.66 PSI)
• Pressure over 0.82 (8.25 bar, 119.66 PSI): Install a pressure limiter between
drinking water connection and hose set.
• The water should be connected only by a competent plumber according to the
local regulations of the appropriate water supply company.
• A cold water connection is necessary for operating the ice maker. The water
pressure must be between 0.17 MPa (1.72 bar, 24.95 PSI) and 0.82 MPa
(8.25 bar, 119.66 PSI). The installation must correspond to the local plumbing
regulations.
• A separate shut-off-valve should be installed in the cold-water inflow.
• The shut-off-valve should not be located behind the appliance. It is
recommended that you mount the shut-off-valve directly next to the appliance or
at another place that is easily accessible.
• When installing the water connection, pay attention to the permissible installation
area for the water line.
• For connection to the drinking water line, use only water pipes that are suitable
for drinking water. Observe national regulations and the connection conditions
of the local water supply companies.
INSTALLATION
WARNING
