ZKTeco Ultima Series Installation Manual Download Page 3

Page: 3 / 31

ULTIMA

INSTALLATION GUIDE | 2019 - v1

Packing list

The contents of the package may vary depending on the modules that you choose.

Mounting Hole

289X155mm

WiringHole

Mounting Hole

(Optional modules)

Mounting Hole

(Optional modules)

Mounting Hole

(Optional modules)

Mounting Hole

(Optional modules)

Baseline

Recommended height from the ground is 1.2 m and can be adjusted according to the personnel average height.

Ultima Mounting template

(Only for reference)

Instruction for using this template:

Before fastening the device, past this template onto the required

installation place, and then drill holes and lay cables according to

the marking on the sticker.

Base

Power Cable

Network Cable

Power Supply

Keys (2)

Mounting template

Optional Modules

Screws & Anchors

Summary of Contents for Ultima Series
































Search results

Summary of Contents for Ultima Series

Reviews:

Related manuals for Ultima Series

Brands by name

Popular brands

ZKTeco Ultima Series, Installation Manual

Search results

Summary of Contents for Ultima Series

Reviews:

Related manuals for Ultima Series

Brands by name

Popular brands