manualshive.com logo in svg

Ziton ZP1-X3, Operation Manual, Page: 19 / 36

Share
Download
Ziton ZP1-X3 Operation Manual Download Page 19

 

ZP1-X3 Operation Manual 

15 

•  Disabled fire sounders are indicated by a steady General Disable LED and a 

steady yellow Fire Sounders LED. 

•  Disabled fire routing is indicated by a steady General Disable LED and a 

steady yellow Fire Routing LED. 

•  Disabled expansion boards are indicated by a steady General Disable LED 

and a steady Expansion I/O Fault/Disabled. 

  Disabled actuators are indicated by a steady General Disable LED and a 

steady yellow Released LED. 

  Disabled safety door monitoring is indicated by a steady General Disable LED 

and a steady Door Fault/Disabled LED. 

  Disabled extinguishing agent flow monitoring is indicated by a steady General 

Disable LED and a steady yellow Extinguishing Agent Flow LED. 

  Disabled extinguishing agent pressure monitoring is indicated by a steady 

General Disable LED and a steady yellow Low Pressure LED. 

  Disabled extinguishing released optical warning panels or signs are indicated 

by a steady General Disable LED and a steady yellow Optical Panel On LED. 

  Disabled start, hold, or abort extinguishing manual call points are indicated by 

a steady General Disable LED and a steady yellow LED for MCP Start, MCP 

Hold, or MCP Abort. 

There is no audible indication. 

Note: 

Some disablements can prevent or disable the extinguishing event. See 

“Extinguishing event prevented” on page 12 for more information. 

Tests 

•  Zone tests are indicated by a steady General Test LED and a steady yellow 

Zone LED. 

•  Extinguishing sounder tests are indicated by a steady General Test LED and 

a steady yellow Extinguishing Sounders On LED. 

•  Fire sounder tests are indicated by a steady General Test LED and a steady 

yellow Fire Sounders LED. 

•  Fire routing tests are indicated by a steady General Test LED and a steady 

yellow Fire Routing LED. 

  Actuator tests are indicated by a steady General Test LED and a steady 

yellow Released LED. 

  Extinguishing agent flow monitoring tests are indicated by a steady General 

Test LED and a steady yellow Extinguishing Agent Flow LED. 

  Extinguishing agent pressure monitoring tests are indicated by a steady 

General Test LED and a steady yellow Low Pressure LED. 

  Extinguishing released optical warning panel or sign tests are indicated by a 

steady General Test LED and a steady yellow Optical Panel On LED. 

Summary of Contents for ZP1-X3





































Reviews:

No comments