TRADEMARKS
Zipato and the Zipato logo are registered Trademarks. All
other product names mentioned herein may be trademarks or
registered trademarks of their respective companies.
NOTICE
Although Zipato has attempted to ensure the accuracy of the content
of this manual, it is possible that this document may contain technical
inaccuracies, typographical, or other errors. Zipato assumes no
liability for any error in this publication, and for damages, whether
direct, indirect, incidental, and consequential or otherwise, that may
result from such error, including, but not limited to loss of data or
profits. Zipato provides this publication “as is” without warranty of any
kind, either express or implied, including, but not limited to implied
warranties of merchantability or fitness for a particular purpose. The
published information in the manual is subject to change without
notice. Zipato reserves the right to make changes in the product
design, layout, and driver revisions without notification to its users.
This version of the Installation guide supersedes all previous versions.
ELECTROMAGNETIC COMPATIBILITY
In proper state and when operated properly, the product complies with
all the requirements in respect of interference radiation according
to EN 301 489-17, EN 301 489-1 and EN 300 328. The connections
conducting HF signals must neither be manipulated nor damaged.
TAKE CARE OF YOUR SAFETY
Display extreme caution when using ladders or steps, please
follow manufacturer’s instructions. Be careful when using hand
and power tools and follow the manufacturer’s guidelines when
using them. Take care that the correct tools are used. Wear
goggles or protective clothing where required.
INTRODUCTION
Presence detector, temperature meter, illuminance meter and
door/window sensor in one device. Zipato Multisensor Quad offers
elaborate security and ambient sensing options. Multifunctional
nature of this product allows you to detect motion, monitor opened/
closed status of any opening object, measure room’s ambient
temperature and light intensity.
When the detector is paired with security appliances, the (1) Door/
window or (2) PIR sensor act as an alarm detector. Alternatively, when
the detector is paired with Z-Wave controller, the detector can support
home automation by detecting both changes in PIR motion detect,
door/window open close status and lux levels, in percentage. Example
scenario: During night, if illuminance levels are lower then preset
value, any person movement in device’s field of vision will trigger
radio signal that will turn connected lightning equipment. In second
example, you can combine door/window sensor and illumination
sensor, and temperature sensor, so when person opens the door,
lights will turn on, and heater/cooler will be activated to adjust room’s
temperature to comfortable levels.
This product can be included and operated in any Z-Wave network
with other Z-Wave certified devices from other manufacturers
and/or other applications. All non-battery operated nodes within
MULTISENSOR
QUAD
QUICK INSTALLATION GUIDE
v1.4
the network will act as repeaters regardless of vendor to increase
reliability of the network.
The device adopt the Z-Wave 500 series chip, which brings following
advantages:
Concurrent multi-channel support reduces external interference.
Better RF range, improves about 10 meters in indoor.
Supports 100 Kbps transmission speeds.
OVERVIEW
PACKAGE CONTENT
1PC
Multisensor Quad
1PC
Sticker pack
1PC
Screws pack
1PC
Quick Installation Guide
FEATURES
Door/Window, motion, temperature and illuminance sensor in
one device
Primarily used as Door/Window sensor, it consists of two parts,
magnet and a sensor
New Z-Wave 500 series chip supports multichannel operation
and higher data rates (9.6/40/100kbps)
Higher output power enhances communication range(+5dBm
output power as compared to -2.5dBm 300 series)
Can be used with various Z-Wave networks/controllers,
regardless of the manufacturers
Very low power consumption
Low battery battery indication
Door/Window status and battery status auto-report
LED indicator
Over-the-air firmware update
Tamper proof protection
Easy installation
SPECIFICATION
PROTOCOL
Z-Wave Plus
POWER
CR123A lithium battery, 1400mAh
OPERATING VOLTAGE
3V
OPERATING CURRENT
45mA
LOW BATTERY VOLTAGE
2.6V
RANGE
min. 40m indoor/100m outdoor in line of sight
TEMPERATURE DETECT RANGE
0° C ~ 40° C
OPERATING TEMPERATURE
-10° C ~ 40° C
TEMPERATURE DETECT ACCURACY
±0.5oC
ILLUMINATION RANGE
0 - 100%
PIR DETECTION RANGE
7m
PIR DETECTION ANGLE
90 Deg.
WEIGHT
49g
DIMENSIONS
Sensor 28 x 95 x 23mm; Magnet 12 x 47 x 9 mm
PACKAGE WEIGHT
68g
PACKAGE DIMENSIONS
68 x 21 x136 mm
BATTERY
1500mAh
MAGNETIC GAP
20 mm
WARRANTY
1 year
MODEL AND FREQUENCIES
EUROPEAN UNION - EU version
ph-psm02.eu / 868.42 MHz
UNITED STATES - US version
ph-psm02.us / 908.42MHz
RUSSIA - RU version
ph-psm02.ru / 869.02MHz
ISRAEL - IS version
ph-psm02.is / 916.02MHz
AUSTRALIA - AU version
ph-psm02.au / 921.42MHz
INDIA - IN version
ph-psm02.in / 865.20MHz
BATTERY INSTALLATION
When the device reports the low battery message. The user should
ILLUMINATION
SENSOR LENS
28.00
3
Profile view
FIGURE 1
Dimensions (unit: mm)
50.00
10.00
28.00
96.00
1
Front view
2
Back view
make your home smart
www.zipato.com
make your home smart
www.zipato.com
01
replace the battery.
To open the front cover please follow below steps.
Using a tool (1) to press 1-1 till you hear a click sound
Hold the front cover and pull back
Hold the front cover and pull up
1
2
2
3
1-1
Replace the new battery and install the cover back.
1. Put the front cover bottom to 1-1, and press down.
2. Push the front cover top to 2-1.
2
1
1-1
2-1
POWER UP PROCEDURE
BATTERY POWER CHECK
When it powers up, the device will detect the power level of the
battery immediately. If the power level is too low, the LED will
continue to flash for about 5 seconds. In that case, replace the
battery.
PIR WARM UP
When it powers up, the PIR need to warm up before operation. The
warm up time about 1 minute, the LED will flash every 2 seconds. After
completing the procedure the LED will light ON three times
NWI
When it powers up, the device will check iif it is already added to the
network. If it isn’t, it will automatically start the NWI mode. The LED
will flash in every second and continue for about 30 seconds, until
timeout or successful inclusion by controller. You can press the tamper
key 3 times to abort the NWI mode.
WAKE
When it powers up, the device will be in wake state for about 20
seconds. During this period, the controller can communicate with
the device. Normally the device is always sleeping to save the
battery energy.
12.35
4
Top/bottom
view
