Zimmer DDOC00734 Instructions Manual Download Page 43

Page: 43 / 46

14 Error diagnosis

INFORMATION

►

For further information on troubleshooting for grippers, refer to the current installation and operating

instructions of the gripper on our website.

►

Please contact Zimmer Customer Service if you have any questions.

15 Resetting to factory settings

NOTICE

When a reset to factory settings is performed, all saved information is deleted.

►

Disconnect the voltage supply.

►

Create a jumper between IO-Link X1 pin 1 (C/Q1) and IO-Link X2 pin 1 (C/Q2).

►

Reconnect the voltage supply.

The SCM initializes and resets the settings.

►

Disconnect the voltage supply.

►

Remove the jumper.

16 Decommissioning/disposal

INFORMATION

When the product reaches the end of its operational phase, it can be completely disassembled and disposed of.

►

Disconnect the product completely from the power supply.

►

Dispose of the components properly according to the material groups.

►

Comply with the locally applicable environmental and disposal regulations.

INSTALLATION AND OPERATING INSTRUCTIONS:

SCM

DDOC00734 / c

EN / 2022-05-09

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

Summary of Contents for DDOC00734















































Search results

Summary of Contents for DDOC00734

Reviews:

Brands by name

Popular brands

Zimmer DDOC00734, Instructions Manual

Search results

Summary of Contents for DDOC00734

Reviews:

Brands by name

Popular brands