manualshive.com logo in svg

Zhone Z-Edge 64, Configuration Manual

Share
Download
Zhone Z-Edge 64 Configuration Manual Download Page 14

Features and capabilities

14

Z-Edge 64 Configuration Guide

 

Figure 2:  Typical Z-Edge 64 network application

Features

The Z-Edge 64 has the following features:

•

Toll-quality voice support with custom calling features

•

Internet Protocol (IP) routing

•

Network Address Translation (NAT) capabilities

•

Dynamic Host Configuration Protocol (DHCP) server/client functionality

•

Simple Network Management Protocol (SNMP) manageability

Protocols and technologies

The Z-Edge 64 supports the following networking protocols and technologies. 
You should have an understanding of these concepts before operating the 
Z-Edge 64:

ATM

Asynchronous Transfer Mode (ATM) is a cell-based, high-speed networking 
technology. The ATM cell has a fixed length of 53 bytes. The cell is broken 
into two parts, the header and the payload. The header (5 bytes) contains the 

Z-Edge 64

Internet

MALC

WAN connection

PSTN

voice lines

LAN
connection

Summary of Contents for Z-Edge 64



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands