manualshive.com logo in svg

Zhone Z-Edge 64, Configuration Manual

Share
Download
Zhone Z-Edge 64 Configuration Manual Download Page 107

Real time statistics

 Z-Edge 64 Configuration Guide

107

 

Enabling and disabling logging

By default logging is enabled on the serial craft port and disabled over 
telnet sessions. To enable or disable logging for the session, using the 
following command:

zSh> log session on | off

The log session command only applies to the current session. You can 
also enable or disable logging for all serial craft port sessions using the 
following command:

zSh> log serial on | off

This command setting persists across system reboots.

Real time statistics

The Z-Edge 64 supports real time statistics using NetHorizhon. Performance 
information is useful for detecting and addressing network problems. For 
information on how to configure and enable this functionality see the 
NetHorizhon User’s Guide.

NetHorizhon monitors performance data on the following ZMS objects 
related to Z-Edge 64:

•

Z-Edge devices

•

Physical ports

•

Logical interfaces

•

Permanent Virtual Circuits (PVCs)

•

IP Routing domains

Note: 

The actual statistics you can view within ZMS for an object 

depend on the type (such as device, performance, or port) and the 
release version of the device on which the object resides.

Saving and restoring configurations

The dump and restore commands enable you to save and restore the system 
configuration. You can save the configuration to the console, or to a file on the 
network. The dump and restore commands use Trivial File Transfer Protocol 
(TFTP) to transfer files to the network. 

Passwords are encrypted when they are saved to the configuration file. The 
encrypted passwords are used to restore the correct password, but cannot be 
used to log in.

Summary of Contents for Z-Edge 64



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands