background image

Page 16                                                                                                          

 MMC-343 Rev - 09/11

MMC-343 Rev - 09/11

13.2

Cable (Electric)

180

8-Cond. Shielded CablePer/ft.

350

8-Cond. Shielded Cable500’ Spool

11811

8-Cond. Shielded Cable1000’ Spool

212

2-Cond. Power CablePer/ft.

349

2-Cond. Power Cable250’ Spool

183

2-Cond. Start Interlock CablePer/ft.

355

2-Cond. Start Interlock Cable250’ Spool

13.3

Wire Harness (Plug)

Replace the # after the Part Number with the length of harness required.  EXAMPLE: 13316-10; 13316-

20; 13316-30

13316-# Serial Communication (Twin Screw) 
13408-# Serial Communication (Multiple Screw)
15544-# Serial Communication - CruiseCommand (Multiple Screw)

13432-# Throttle, Voltage
13494-# Throttle, Current
13533-# Throttle, PWM
14363-# Throttle, MAN
15027-# Throttle, Frequency

13322-# Clutch – Ahead/Astern/Clutch Power
13324-# Clutch – Ahead/Astern/Neutral/Clutch Power
13240-# Clutch – Ahead/Astern/Troll/Troll CMD/Clutch Power
14310-# Clutch – Ahead/Astern/Troll CMD/Clutch Power
14925-# MAN with Troll
14542-# MAN without Troll

13239-# Magnetic Pickup or Pulse Transmitter

13422-# ZF Autotroll (MS70-13231 only)
15364-

ZF Autotroll (MS570-15382 Cannon Connector only)

15208-

ZF Autotroll (MS570-15382 Harting Connector only)

13552-# Power/Start Interlock/Clutch Pressure
13756-# Power/Start Interlock
15023-# Power

13557-# Control Head - 1 Connector
14261-# Control Head - 2 Connectors

13.4

Test Unit

13927

Service Field Test Unit

14000

Field Test Control Head - Dual

Summary of Contents for MMC-343















Reviews: