ZF Marine ClearCommand 9000 Series, Installation, Operation And Troubleshooting Manual

Page: 206 / 272

TROUBLESHOOTING
PageB8-1
B8 ERROR CODES
As stated previously, if a problem with the Control Sys-
tem is detected, the Processor is programmed to display
numerous Error Codes to aid in the isolation of the
cause. The following tables list these Error Codes, along
with a brief description
.
B8-4 C
LUTCH
S
OLENOID
E
RROR
C
ODES
B8-5 T
ROLL
S
OLENOID
E
RROR
C
ODES
B8-6 B
ASIC
C
ONTROL
S
YSTEM
E
RROR
C
ODES
Table B8-4: Clutch Solenoid Control System Error Codes
Error
No.
Title Description
1 Clutch Astern Shorted The Astern Clutch Solenoid is requiring more current than expected.
2 Clutch Astern Open The Astern Clutch Solenoid should be drawing current but is not.
3 Clutch Neutral Shorted The Neutral Clutch Solenoid is requiring more current than expected.
4 Clutch Neutral Open The Neutral Clutch Solenoid should be drawing current but is not.
5 Clutch Ahead Shorted The Ahead Clutch Solenoid is requiring more current than expected.
6 Clutch Ahead Open The Ahead Clutch Solenoid should be drawing current but is not.
Table B8-5: Troll Solenoid Control System Error Codes
Error
No.
Title Description
7 Troll ON/OFF Shorted The Troll ON/OFF Solenoid is requiring more current than expected.
8 Troll ON/OFF Open The Troll ON/OFF Solenoid should be drawing current but is not.
9 Troll Command Shorted The Troll Proportional Solenoid is requiring more current than expected.
10 Troll Command Open The Troll Proportional Solenoid should be drawing current but is not.
Table B8-6: Basic Control System Error Codes
Error
No.
Title Description
13 Station No.1
Faulted High
Station No.1 Control Head’s lever position is out of range.
The input appears to be too high.
14 Station No.2
Faulted High
Station No.2 Control Head’s lever position is out of range.
The input appears to be too high.
15 Station No.3
Faulted High
Station No.3 Control Head’s lever position is out of range.
The input appears to be too high.
16 Station No.4
Faulted High
Station No.4 Control Head’s lever position is out of range.
The input appears to be too high.
17 Station No.5
Faulted High
Station No.5 Control Head’s lever position is out of range.
The input appears to be too high.
18 Station No.6
Faulted High
Station No.6 Control Head’s lever position is out of range.
The input appears to be too high.
19 Station No.7
Faulted High
Station No.7 Control Head’s lever position is out of range.
The input appears to be too high.
20 Station No.8
Faulted High
Station No.8 Control Head’s lever position is out of range.
The input appears to be too high.
21 Station No.9
Faulted High
Station No.9 Control Head’s lever position is out of range.
The input appears to be too high.
22 Station No.10
Faulted High
Station No.10 Control Head’s lever position is out of range.
The input appears to be too high.
23 Station No.1
Faulted Low
Station No.1 Control Head’s lever position is out of range.
The input appears to be too low.
24 Station No.2
Faulted Low
Station No.2 Control Head’s lever position is out of range.
The input appears to be too low.
25 Station No.3
Faulted Low
Station No.3 Control Head’s lever position is out of range.
The input appears to be too low.