Home
/
Zero Motorcycles
/
S 2021
/
Owner'S Manual

Zero Motorcycles S 2021, Owner'S Manual

Share

Page: 41 / 160

background image

Controls and Components

3.21

Front Brake Lever Adjuster

The position of the front brake lever can be adjusted by turning
the adjustment knob (A) located on the master cylinder
assembly. Turning the knob clockwise or counter-clockwise will
adjust the distance between the lever and the throttle control.

Parking Brake Operation (if equipped)

Your Zero Motorcycle may be equipped with a parking brake
system. When applied, the parking brake will prevent your
motorcycle from rolling forward or backward.

A.

Parking Brake ON

Parking brake lever pointing away from the motorcycle.

B.

Parking Brake OFF

Parking brake lever pointing toward the center of the
motorcycle.

Zero Owner's Manual (S and DS).book Page 21 Monday, September 21, 2020 11:43 AM

«
...
39
40
41
42
43
...
»

Summary of Contents for S 2021

































































































































































Reviews:

No comments

Related manuals for S 2021

Brand: 3M Pages: 26

Brand: Tao Motor Pages: 3

Brand: Bajaj Pages: 55

B40 VICTOR W D 1967

Brand: BSA Pages: 128

Brand: KSR Moto Pages: 51

LOCK-IT 506007-7

Brand: hepco & becker Pages: 2

Brand: Denali Pages: 2

KAWASAKI ZX6R 2007/8

Brand: Evotech Performance Pages: 2

Brand: PUIG Pages: 3

Brand: Dynafit Pages: 52

Super Meteor 650

Brand: Royal Enfield Pages: 124

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

XVS950A Midnight Star

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands