manualshive.com logo in svg

Zero Motorcycles DS 2021, Owner'S Manual

Share
Download
Zero Motorcycles DS 2021 Owner'S Manual Download Page 42

Controls and Components

3.22

Tank Storage Compartment

Unless other optional equipment is specified on your Zero 
Motorcycle, a lockable tank storage compartment will be 
installed as standard. The storage compartment lid can be 
locked/unlocked using the ignition key.

Located under the edge of the compartment lid are two studs, 
which can be used to secure the supplied helmet leash cable.

Using the helmet leash cable

1. Open tank storage compartment lid. 

2. Thread leash through chin strap buckles. 

3. Thread leash through second leash eye. 

4. Place leash eye over tank storage compartment stud. 

5. Close tank storage compartment lid and lock with key. 

6. Place helmet securely on tank storage compartment lid. 

Zero Owner's Manual (S and DS).book  Page 22  Monday, September 21, 2020  11:43 AM

Summary of Contents for DS 2021

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands