background image

www.zephyronline.com

 IMPORTANT SAFETY INSTRUCTIONS

 

FOR RESIDENTIAL USE ONLY

 

READ AND SAVE THESE INSTRUCTIONS

 PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

 

IMPORTANT

: Save these Instructions for the Local Electrical Inspectors use.

 

INSTALLER

: Please leave these Instructions with this unit for the owner.

 OWNER

: Please retain these instructions for future reference.

 Take care when using cleaning agents or detergents.
 Suitable for use in household cooking area

 WARNING

 - To reduce the risk of fi re or electric shock, do not use this fan 

with any Solid-State Speed Control Device.

 CAUTION

 - To reduce risk of fi re and to properly exhaust air, be sure to duct 

air outside – Do not vent exhaust air into spaces within walls or ceilings or into 
attics, crawl spaces, or garages.

 CAUTION

 - For general ventilating use only. Do not use to exhaust hazardous 

or explosive materials and vapors.

 

CAUTION

 - To avoid motor bearing damage and noisy and/or unbalanced 

impellers, keep drywall spray, construction dust, etc. off  power unit.

 CAUTION

 - Please read specifi cation label on product for further information 

and requirements.

 WARNING

 – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO 

PERSONS, OBSERVE THE FOLLOWING:

A. 

Use this unit only in the manner intended by the manufacturer. If you have 

ques        tions, contact the manufacturer.

B.

 Before servicing or cleaning unit, switch power off  at service panel and lock   

the service disconnecting means to prevent power from being switched on ac-
cidentally. When the service disconnecting means cannot be locked, securely    
fasten a prominent warning device, such as a tag, to the service panel.

 WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A.

 Never leave surface units unattended at high settings. Boilovers cause smo-

king and greasy spillovers that may ignite. Heat oils slowly on low or medium 

S

a

fe

ty instruc

tions

- 4 - 

Summary of Contents for Range Hood APN-M90AWX





















Reviews: