6
7
8
Improperly installed ceiling sweep fans can
be dangerous and expensive to repair and will
void guarantee.
This fan is designed for indoor use only, ta=40°C.
Do not mount in positions where fan is subject to
water or moisture.
The fan must be installed so that the blades are
greater than 2.1 metres from floor.
All wiring must comply with the requirements of
Australian and New Zealand Standard AS/NZ 3000.
The fan blades supplied for this fan are matched to
minimize wobble. If installing more than one fan do
not mix blade sets.
Warning:
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instructions concerning use of appliance by a
person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Note: this faN must be iNstalled by a liceNse electrical coNtractor.
Trouble
Problem Cause
Suggested Remedy
Fan will not start
a Fuse or circuit breaker blown
b Loose power line connections
to the fan.
c Reversing switch (where
applicable) neither up or down.
a Check main and branch circuit fuses or
circuit breakers.
b Check line wire connections to fan.
c Push switch either fully up or down.
Fan wobbles
a Fan blades not horizontal
to ceiling
b Blade screws are loose
a Measure from ceiling to tip of blades, then
rotate fan so all 6 blades are checked for
equal height from ceiling.
(Note: adjustments may be made by slight
pressure up or down on blade holders).
Make sure all screws are securely
fastened.
Fan sounds noisy
a Incorrect bulb(s) being used in
light kit.
b Loose fan blade screws
c Ceiling fan not secured
against ceiling
d Incorrect speed controller
a Check suggested bulb(s) in light kit
b Re-tighten all screws on fan blades but
never over-tighten
c Re-tighten all screws in the hanging
bracket or plate.
d Change the controller to the one supplied.
Mechanical Noise
a Allow for at least 8 hours settling-in period.
Warranty
Arlec guarantees this product in accordance with the Australian Consumer Law.
Arlec also warrants to the original first purchaser of this product (“you”) from a retailer that this product will be free of defects in materials and
workmanship for a period of 12 months from the date of purchase; provided the product is not used or installed other than for the purpose, or
in a manner not within the scope of the recommendations and limitations, specified by Arlec, is new and not damaged at the time of purchase,
has been properly installed by a licensed electrician or contractor who is licensed to install electrical products in the place in which the
product was installed and in accordance with Arlec’s installation instructions, has been maintained in accordance with the recommendations
specified by Arlec, has not been subjected to abuse, misuse, neglect or damage, has not been modified or repaired without the approval of
Arlec and has not been used for, or installed in premises which are used for, commercial purposes (“Warranty”).
If you wish to claim on the Warranty, you must, at your own expense, return the product or that part of the product which you believe is
defective in materials and workmanship, and provide proof of original purchase, your name, address and telephone number and a certificate
of installation or other document required by law for the installation of electrical products in the place in which the product was installed issued
by the licensed electrician or contractor who installed the product, to Arlec at the address below within 12 months from the date of purchase.
Please note that the Warranty does not cover removal or re-installation of the product or that part of the product which you believe is defective.
Arlec will assess any claim you may make on the Warranty in the above manner and if, in Arlec’s reasonable opinion, the Warranty applies,
Arlec will at its own option and expense replace the product (or part of the product) with the same or similar product (or part of the product) or
repair the product (or part of the product) and return it to you or refund the price you paid for the product. Arlec will bear its own expenses of
doing those things, and you must bear any other expenses of claiming on the Warranty.
The Warranty is in addition to other rights and remedies you may have under a law in relation to the product to which the Warranty relates.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.
Arlec’s telephone number, address and email address are:
Customer Service: (03) 9982 5111
New Zealand Toll Free: 0800 003 329
Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130
Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130
Email: [email protected]
CPIN00XXXX
CSF5610
CSF5612
CeIlINg FAN ASSembly
AND INSTAllATIoN
INSTRuCTIoNS
PAIRINg AND uSINg blueTooTh FuNCTIoN
TRouble ShooTINg CheCKlIST
Press and release the Bluetooth button.
This action will result in the following:
• The Bluetooth icon will appear on the
LCD screen of the transmitter handset.
• The blue LED ring on the bottom of the fan
(surrounding the speaker) will illuminate.
• The words “Power On” will be heard
from the speaker.
• Pairing mode will be activated.
Turn on the Bluetooth function on your device (phone,
Ipad, computer, etc.) and search or scan for the fan.
Upon scanning “Zenta” will appear on your list of
devices. Select “Zenta” and continue to pair with the
fan. Enter “8888”as the pairing code from your device.
When Bluetooth function has successfully connected,
the words “Pairing Completed” will be heard from the
speaker. Now you can send your audio tracks directly
to the speaker in the fan and use your device volume to
adjust the sound.
To pair another device, switch off the Bluetooth function
by pressing the Bluetooth button, then turn on again
and repeat above procedure
Please note that you only need to pair your device once
with the fan. After initial pairing you can connect by
selecting “Zenta”, which has already been stored in
your device.
Bluetooth
button
Bluetooth Appears on
LCD Screen
Blue LED Ring
CPIN00XXXX
Care and Cleaning
Periodic cleaning of your new ceiling fan is
the only maintenance that is needed. Use a
soft brush or lint free cloth to avoid scratching
the finish.
Do not use water when cleaning your ceiling fan,
it could damage the motor or the wood blades
and create the possibility of an electrical shock.
Motor has permanently lubricated ball bearings.
No need to oil.
This fan is not intended for use by young children
or infirm persons without supervision.
Do not allow young children to play with the fan.
Wobble
Ceiling fans tend to move during operation
due to the fact that they are not generally
rigidly mounted - if they were, they could
generate excessive ceiling vibration and stress
on their mountings.
Movement of a couple of centimetres is quite OK
and does not suggest the fan will fall down.
Ceiling fans are mounted very securely on steel
brackets with rubber cushioning or with ball joints
to allow free movement.
Please note that all ceiling fans are not the same,
even in the same model - some may move more
or less than others.
The following procedures should eliminate any
wobble. Check for wobble after each step. It is
impossible to eliminate wobble completely.
a
Check that all blade brackets are
tightened securely.
b
Most wobble problems result from inconsistent
blade level. To check blade level, measure the
distance from each blade tip to the ceiling. If
measurements are inconsistent, adjustments
of brackets will be required.
C
Wobble problem could also result from
deviations in distance from blade to blade.
To check blade separation, measure the
distance from blade tip to blade tip.
Should measurements vary, loosen screws
connecting blades and brackets (one at a
time) then shift blade to proper position and
re-tighten screws.
normal Wear and Tear
Threaded components working slightly loose or
blade carriers even slightly bent due to vigorous
cleaning or bumping can cause extra wobble and
noise. This is not covered under guarantee - but
a little care and maintenance can reduce or
prevent this problem.
bumps-in-The-nighT
This is the biggest cause for service calls which
are outside the manufacturer’s warranty. If a fan
has a fault, it will be noticeable at all times.
Naturally when everything is quiet at night, you
will be more inclined to hear small noises which
may not be noticeable at other times. Even slight
power fluctuations, and mains frequency signals
superimposed in you electricity supply for off-
peak hot water control may cause a change in
fan motor noise. This is normal.
Fan lighTs
Except for actual faults in manufacture, which are
extremely rare, Fan light glass and globes are not
covered under your guarantee. Noises and
vibrations etc are often more accentuated when a
fan light is fitted.
For instance, a fan light glass that has not been
tightened or worked loose can cause a rattle.
Again, care and maintenance will reduce this.
All electrical motors, including fans make
some noise and may feel hot if touched -
this is not a fault.
summer/WinTer operaTion
This fan incorporates a reversing function that
changes tha direction of the motor.
When set in the Normal position the airflow
is directed downwards. This is best for
Summer cooling.
When set in the reverse position the airflow is
directed upward. This is best for Winter
operation, as it assist in moving air around the
room, maknig heating more efficient.