Zenoah LZ 2146 CD, Operator'S Manual

Page: 8 / 268

Do not use the product if the muffler is missing or
defective. A defective muffler increases the noise level
and the risk of fire.
CAUTION: The muffler becomes very hot
during and after use and when the engine
operates at idle speed. Be careful near
flammable materials and/or fumes to prevent
fire.
To do a check of the muffler
• Examine the muffler regularly to make sure that it is
attached correctly and not damaged.
Fuel safety
WARNING: Read the warning instructions
that follow before you use the product.
• Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry.
• If you spill fuel on your clothing, change clothing
immediately.
• Do not get fuel on your body, it can cause injury. If
you get fuel on your body, use soap and water to
remove the fuel.
• Do not start the product if the engine has a leak.
Examine the engine for leaks regularly.
• Be careful with fuel. Fuel is flammable and the fumes
are explosive and can cause injuries or death.
• Do not breathe in the fuel fumes, it can cause injury.
Make sure that there is a sufficient airflow.
• Do not smoke near the fuel or the engine.
• Do not put warm objects near the fuel or the engine.
• Do not add the fuel when the engine is on.
• Make sure that the engine is cool before you refuel.
• Before you refuel, open the fuel tank cap slowly and
release the pressure carefully.
• Do not add fuel to the engine in an indoor area. Not
sufficient airflow can cause injury or death because
of asphyxiation or carbon monoxide.
• Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
• Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank before a start.
• Do not put too much fuel in the fuel tank.
Safety instructions for maintenance
WARNING: Read the warning instructions
that follow before you use the product.
• The exhaust fumes from the engine contain carbon
monoxide, an odourless, poisonous and very
dangerous gas. Do not start the engine indoors or in
closed spaces.
• Before you do the maintenance on the product, stop
the engine and remove the ignition cable from the
spark plug.
• Use protective gloves when you do maintenance on
the cutting equipment. The blade is very sharp and
cuts can easily occur.
• Accessories and changes to the product that are not
approved by the manufacturer, can cause serious
injury or death. Do not change the product. Always
use accessories that are approved by the
manufacturer.
• If the maintenance is not done correctly and
regularly, the risk of injury and damage to the
product increases.
• Only do the maintenance as given in this owner's
manual. All other servicing must be done by an
approved Zenoah service agent.
• Let an approved Zenoah service agent do servicing
on the product regularly.
• Replace damaged, worn or broken parts.
Assembly
To assemble the handle
1. Align the screw holes at the bottom of the lower
handle with the screw holes in the lower handle
assembly on the deck.
2. Attach the screws, washers and knobs.(Fig. 24 )
3. Use the straps to attach the cables to the handle.
(Fig. 25 )
Note: Make sure that the tension in the cables is not
too high.
4. To set the handle height, loosen the lower knobs, lift
or lower the handle to adjust the height, and then
tighten the knobs fully.(Fig. 26 )
To install the starter rope
1. Attach the loop for the starter rope and the T-knob.
Do not tighten fully.(Fig. 27 )
2. Hold the engine brake handle against the handlebar.
3. Slowly pull out the starter rope and put it into the
loop for the starter rope.(Fig. 28 )
4. Tighten the T-knob.(Fig. 29 )
To assemble the grass catcher
1. Put the upper part of the grass catcher onto the
lower part of the grass catcher.
2. Attach the grass catcher frame with the clips.(Fig.
30 )
8 899 - 002 - 27.09.2018