our depth gauge tool to acheive the correct depth gauge
setting and bevel for the depth gauge.
1. Place the depth gauge tool over the saw chain.
Detailed information regarding how to use the depth
gauge tool, will be found on the package of the depth
gauge tool.
2. File off the tip of the depth gauge that protrudes
through the depth gauge tool. Use the flat file.
The depth gauge setting is correct when you no longer
feel resistance as you draw the file along the depth
gauge tool.
To tension the saw chain
WARNING: A slack saw chain may jump off
and cause serious injury or death.
The more you use a saw chain the longer it becomes. It
is therefore important to adjust the saw chain regularly
to take up the slack.
Do a check of the chain tension every time you refuel.
Tension the saw chain as tightly as possible, but not so
tight that you cannot pull it round freely by hand.
Note: A new saw chain has a running-in period during
which you should do a check of the tension more
frequently.
1. Undo the bar nuts that hold the clutch cover/chain
brake. Use the combination spanner.
2. Raise the tip of the bar and stretch the saw chain by
tightening the chain tensioning screw. Use the
combination spanner. Tighten the saw chain until it
does not sag from the underside of the bar.
3. Tighten the bar nuts using the combination spanner
and lift the tip of the bar at the same time.
4. Make sure that you can pull the saw chain round
freely by hand and that it does not sag from the
underside of the bar.
The position of the chain tensioning screw on our
chainsaws varies from model to model. See instructions
Product overview GZ3500T on page
2
to find out where it is on your model.
Lubrication of the cutting equipment
To do a check of the saw chain lubrication
Do a check of the chain saw lubrication each time you
refuel.
1. Start the product and let it run at 3/4 throttle. Aim the
tip of the bar at a light coloured surface about 20 cm
(8 inches) away.
28
308 - 004 - 27.09.2017
Summary of Contents for GZ3500T
