5. Assemble the clutch cover and steer the chain
adjuster pin to the hole in the guide bar. Make sure
that the drive links of the saw chain fit correctly on
the drive sprocket. Also make sure that the saw
chain is correctly engaged in the groove in the guide
bar. Tighten the bar nuts finger tight.
6. Tighten the saw chain by turning the chain
tensioning screw clockwise with the combination
spanner. Tighten the saw chain until it does not sag
from below the guide bar. See instructions under the
To tension the saw chain on page 28
7. The saw chain is tightened correctly as it does not
sag from the below the guide bar, but you can turn it
easily by hand. Hold up the guide bar tip and tighten
the bar nuts with the combination spanner.
8. Do a check of the chain tension frequently, after you
have assembled a new saw chain, until the saw
chain is run-in.
9. Do a check of the chain tension regularly. A correct
chain tension results in good cutting performance
and a long life.
To assemble a spiked bumper
To assemble a spiked bumper, consult your servicing
dealer.
Operation
Introduction
WARNING: Read and understand the safety
chapter before you use the product.
WARNING: Always wear personal protective
equipment. See heading
equipment on page 6
To do a function check before you use
the product
1. Do a check of the chain brake to make sure that it
operates correctly and that it is not damaged.
2. Do a check of the throttle trigger lockout to make
sure that it operates correctly and that it is not
damaged.
3. Do a check of the start/stop switch to make sure that
it operates correctly and that it is not damaged.
4. Make sure that there is no oil on the handles.
5. Do a check of the anti vibration system to make sure
that it operates correctly and that it is not damaged.
6. Do a check of the muffler to make sure that it is
correctly attached and that it is not damaged.
7. Do a check of the chainsaw to make sure that all
parts are correctly attached and not damaged or
missing.
8. Do a check of the chain catcher to make sure that it
is attached correctly.
308 - 004 - 27.09.2017
13
Summary of Contents for GZ3500T
