© Zennio Avance y Tecnología S.L.
Edition 1
Further information
Page 1/2
DALI BOX Broadcast 4CH v2
KNX - DALI Broadcast Interface for up to 4 channels
ZDIDLB4V2
TECHNICAL DOCUMENTATION
FEATURES
•
Control of 4 channels with up to 64 DALI ballasts per channel
•
Single Master DALI-2 Controller
•
Compatibility with color ballasts (DT8)
•
Supports KNX Data Secure
•
Ballast replacement allowed with automatic detection
•
Error detection and monitoring (except multiaddress DALI ballasts)
•
Burn-in, Stand-by and Auto-off functionality for each channel
•
Optional manual dimming control
•
External 110-240 VAC 50/60 Hz power supply
•
Total data saving on KNX bus failure
•
Integrated KNX BCU (TP1-256)
•
Dimensions 67 x 90 x 79 mm (4.5 DIN units)
•
DIN rail mounting according to IEC 60715 TH35, with fixing clamp
•
DALI Standard certified according to IEC 62386
•
Conformity with the CE, UKCA, RCM directives (marks on the right
side)
Figure 1: DALI BOX Broadcast 4CH v2
GENERAL SPECIFICATIONS
CONCEPT
DESCRIPTION
Type of device
Electric operation control device
KNX supply
Voltage (typical)
29 VDC SELV
Voltage range
21-31 VDC
Maximum
consumption
Voltage
mA
mW
29 VDC (typical)
3.3
95.7
24 VDC¹
10
240
Connection type
Typical TP1 bus connector for 0.8 mm Ø rigid cable
External power
supply
Voltage
110-240 VAC 50/60 Hz PF=0.5
Maximum consumption
175 mA @ 110 VAC / 100 mA @ 230 VAC
Operation temperature
-5 .. +45 °C
Storage temperature
-20 .. +55 °C
Operation humidity
5 .. 95%
Storage humidity
5 .. 95%
Complementary characteristics
Class B
Protection class / Overvoltage category
II / III (4200 V)
Operation type
Continuous operation
Device action type
Type 1
Electrical stress period
Long
Degree of protection
IP20, clean environment
Installation
Independent device to be mounted inside electrical panels with DIN rail (IEC
60715)
Minimum clearances
Not required
Response on KNX bus failure
Data saving according to parameterization
Response on KNX bus restart
Data recovery according to parameterization
Operation indicator
The programming LED indicates programming mode (red) and test mode
(green). Each output LED indicates its status (fixed = active output; flashing
= error in the output). Power supply LED indicates the presence of supply
voltage (green).
Weight
221 g
PCB CTI index
175 V
Housing material
PC FR V0 halogen free
¹ Maximum consumption in the worst-case scenario (KNX Fan-In model).
Programming/Test button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe
mode. If this button is held for more than 3 seconds, the device enters the test mode. In order to perform a KNX Secure factory reset, while the device is
in safe mode, press the button for 10 seconds until the programming LED changes its state.
Programming/Test LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. The test mode is
indicated by the green color. During the start-up (reset or after KNX bus failure) and if the device is not in safe mode, it emits a red flash.
1. DALI channel status LED
2. DALI channel control button
3. Programming/Test LED
4. Programming/Test button
5. DALI channel output
6. External supply LED
7. External power supply
8. KNX connector
1
6
2
5
4
3
7
8