Zeiss CONTURA Operating Instructions Manual Download Page 135

Page: 135 / 158

Care

61211-1310402

CONTURA

9-5

Safety instructions

WARNING

Risk of injury caused by travel movements.

Crushing and cutting of body parts.

When carrying out care measures, make sure that no travel move-
ments are performed.

Switch the drives off in order to enable safe execution of the care
measures.

CAUTION

Injuries can be caused by sharp edges.

Cutting or tearing of the skin.

Be very careful and wear appropriate clothing, if required, e.g.
gloves.

CAUTION

There is a risk of injury if filters are replaced under pressure.

Switch off the compressed air before replacing the air filters.

Disconnect the compressed-air supply from the power supply.

Make sure to depressurize the line.

Measures of precaution

Contamination of components by compressed air.

The functioning of some sensitive components may become impaired
by dust particles.

not use compressed air

for cleaning the CMM.

NOTE

Use

grease-dissolving

and

non-corroding

cleaning agents.

NOTE

Preventive care also includes making sure that all workpieces to be mea-
sured are clean. The workpieces must be free from machining residues
(e.g. metal chips, oil) and dust.

Clean the workpieces before placing them on the measuring table.

Summary of Contents for CONTURA































































































































































Search results

Summary of Contents for CONTURA

Reviews:

Related manuals for CONTURA

Brands by name

Popular brands

Zeiss CONTURA, Operating Instructions Manual

Search results

Summary of Contents for CONTURA

Reviews:

Related manuals for CONTURA

Brands by name

Popular brands