zeeltronic PDCI-11V User Manual Download Page 1

 

 

- 1 - 

 

www.zeeltronic.com 
[email protected] 
 
updated 06.08.2014 
program version: 25.120326 
 

USER MANUAL  

PDCI-11V PROGRAMMABLE CDI IGNITION AND PV CONTROLLER 

 
 

 

TECHNICAL DATA 
 
Limit values: 
- minimum revs 

280 RPM 

- maximum revs 

20000 RPM 

- minimum supply voltage 

9 Volts 

- maximum supply voltage 

18 Volts 

- max idle current draw  

                     50 mAmp 

- maximum continuous current for shift light and power jet output 

1 Amp  

- peak current for shift light and power jet output  

5 Amp 

- constant spark energy from idle to 20000 RPM 

>65mJ 

 
Circuit is protected against reverse supply voltage (wrong connection). 
 
Features: 
- one channel isolated input (pickup) 
- store and load function for two ignition curves 
- TPS input (Throttle Position Sensor) 
- shift light output 
- 2 power jet outputs 
- quick shift (shift kill) 
- soft rev limit (three stage rev limit) 
- external switch for changing ignition map while riding 
- tachometer output 
- easy and fast programming on the field, via hand held programmer 
- programming while machine running - you can immediately see effects 
- each curve can be set in 4 to 12 curve points 
- 3D interpolated ignition map, if TPS selected 
- signal delay compensation 
- instant monitoring of rev's and angle, via LCD(hand held programmer) 
- programmable power valve actuation 
- store and load function for 5 PV curves 
- external switch for changing PV map while riding 
- programmable PV deviation 
- programmable max close and max open positions 
- self PV test on power-up 

Summary of Contents for PDCI-11V















Reviews: