background image

10

SOMETHING NOT WORKING

Symptom

No power to the appliance

The light does not come on 

The temperature in the fridge section is too high

The compressor runs continously

Noise

Water under the salad bin

Solution

Check there is power at the socket.

Check there is not a power cut by checking the
household lights.

Check the fuse has not blown.

Ensure that the bulb is correctly fitted.

Replace the bulb if it has blown.

Check the door light switch is not jammed.

Check the temperature in the fridge is turned to the
correct setting relative to ambient conditions.

Check the ambient temperature is within the
applianceÕs operating limits of 10¡C  to 32¡C. 

Adjust the thermostat to give correct temperature
control. See ÒSetting the temperatureÓ.

Check that the doors are closed.

Large quantities of food have recently been placed in
the cabinet/and or door is frequently opened.

Check that air ventilation is not obstructed.

Refer to normal operating sounds.

Check the drain hole is not blocked. (see
Maintenance and Cleaning).

Important:

If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or

installation a charge will be made, even if the appliance is under guarantee.

Before 

contacting your local Service Force Centre, check the following points:

If, after the above checks, there is still a fault, call your local Service Force Centre.

In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.

Please note that proof of purchase is required for any in-guarantee service call

Summary of Contents for ZU 7115





















Reviews: