2-CHANNEL RADIO MODULAR RECEIVER ROM-10
MANUAL INSTRUCTION
ZAMEL
Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04
www.zamelcet.com
, e-mail: [email protected]
VER. 003_20.05.2011
APPEARANCE
TECHNICAL DATA
ROM-10
Input (supply) terminals: L, N
Input rated voltage: 230V AC
Input voltage tolerance: -15 ÷ +10 %
Nominal frequency: 50 / 60 Hz
Nominal power consumption: 0,55 W
Optic signalling of power supply: LED green diode
Number of operation modes: 5
Number of channels: 2
Transmission: radio 868,32 MHz
Coding way: unidirectional
Coding: addressing transmission
Maximum number of remote controls: 32
Range: up to 300 m in the open area
Time adjustment: 1 sec. ÷ 18 hours (every second)
Optic signalling of relay status: 2 x LED red diode
2 x LED red diode 12, 11, 14, 24, 21, 22
Relay contact parameters: 2NO/NC 8A / 250V~ AC1 2000 VA
Ambient temperature range: -10 ÷ +55
o
C
Section of connecting cables: do 2,5 mm
2
Operating position: free
Casing mounting: TH-35 rail (according to EN 60715)
Casing protection degree: IP20 (EN 60529)
Protection level: II
Overvoltage category: II
Pollution degree: 2
Surge voltage: 1 kV (EN 61000-4-5)
Dimensions: monomodular casing (17,5 mm) 90 x 17,5 x 66 mm
Weight: 0,087 kg
Reference standard: EN 60669, EN 60950, EN 61000
The device is designed for
single-phase installation and
must be installed in accord-
ance with standards valid in
a particular country. The device
should be connected according
to the details included in this
operating manual. Installation, connection and
control should be carried out by a qualified electri-
cian staff, who act in accordance with the service
manual and the device functions.
In case of casing dismantling an electric shock
may occur, and the guarantee is lost then. Before
installation make sure the connection cables are
not under voltage. The cruciform head screwdriver
3,5 mm should be used to instal the device. Im-
proper transport, storage, and use of the device
influence its wrong functioning. It is not advisable
to instal the device in the following cases: if any
device part is missing or the device is damaged
or deformed. In case of improper functioning
of the device contact the producer.
CAuTIoN!
FEATuRES
DESCRIPTIoN
● cooperation with wireless EXTA FREE
system transmitters,
● 2-channel radio receiver mounted on
a TH-35 rail in a distribution board,
● five operation modes: switching on mode,
switching off, monostable, bistable, time,
● two output relays 8A (changeover
contacts),
● wide range of operation (up to 300 m),
● power supply and relay operation are opti-
cally signalled,
● integration possibility with wired control
systems (e.g. exta home automation),
● connection possibility of ANT-01 antenna
mounted not in the distribution board,
● possibility of widening operation range by
means of RTN-01 retransmitter.
2-channel radio modular receiver ROM-
10 can be mounted in distribution boards on
the TH-35 rail and can realise radio control
functions using any of EXTA FREE system
transmitters. Any electric system realising
radio system functions can be connected to
the device relay output (e.g. wired devices of
EXTA home automation, relay-contactor sys-
tems and others).
The symbol means selective
collecting of electrical and electronic
equipment.
It is forbidden to put the used
equipment together with other waste.
Optic signalling of input voltage
Optic signalling of relay 1 status (channel 1)
Optic signalling of relay 2 status (channel 2)
Antenna’s socket
Programming push-buttons (PROG 1, PROG 2)
Input (supply) terminals (L, N)
Relay output terminals (12, 11, 14, 24, 21, 22)
Antenna
CoNNECTIoN
APPLICATIoN
Radio modular receiver
ROM-10 operates as
a receiver of P-257/4
4-channel remote control
(control of lighting
operation in front of
and inside the garage).
Additionally P-257/4
remote control can
control operation of ROB-
01/12-24V radio gate
controller.
CAPACITY
1000W
250W
500W
375W
MouNTING
1. Disconnect power supply by the phase
fuse, the circuit-breaker or the switch-
disconnector combined to the proper
circuit.
2. Check if there is no voltage on
connection cables by means of
a special measure equipment.
3. Connect the cables with the terminals in
accordance with the installing diagram.
4. mount ROM-10 device on a TH-35 rail.
5.
Switch on the power supply from
the mains.
WARRANTY CARD
There is 24 months guarantee on the product
1. ZAMEL provides a two-year warranty for its products.
2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances
b) defects resulting from incorrect installation or operation of ZAMEL products; c) defects resulting from any changes made by CUS-
TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold; d) defects resulting
from force majeure or other aleatory events for which ZAMEL is not liable; e) power supply (batteries) to be equipped with a device
in the moment of sale (if they appear);
3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect.;
4. ZAMEL will review complaints in accordance with existing regulations.;
5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL.
6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy
between the goods and the contract.
Salesman stamp and signature, date of sale
The ZAMEL company devices
which are characterised with
this sign can cooperate with
each other.
