Z3 Technology Z3-DME-03 User Instructions Download Page 31 | Manualshive

Page: 31 / 54

background image

DOC-USR-0061-03

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

31

6.12

Encoding Closed Caption Data

The Z3-DME-03 supports extraction of closed caption data from composite or SDI input. This
automatically occurs any time composite or SDI input with closed caption data included is used.
Encoding and subsequently extracting closed caption data from composite is shown below:

Connect a composite input with closed caption data to the composite connector. Also connect the

audio if available:

Configure the Encoder to use composite input:

Connect composite with CC data

Figure 37 Connections for Closed Caption Extraction

Figure 38 Sample Encoder Settings for Composite Closed Caption Extraction

«
...
29
30
31
32
33
...
»

Summary of Contents for Z3-DME-03























































Reviews:

No comments

Related manuals for Z3-DME-03

TopTronic E Solar TTE-SOL

Brand: Hoval Pages: 95

Rossini Transport

Brand: DCS Pages: 31

Brand: Lechpol Pages: 2

Brand: Linear Technology Pages: 26

Brand: Digitus Pages: 3

Brand: Elation Pages: 4

Brand: Transition Networks Pages: 5

Brand: Eleris Pages: 184

Brand: Gyrus Acmi Pages: 60

NetworkHD 100 series

Brand: Wyrestorm Pages: 2

Brand: GUSTARD Pages: 22

Brand: GPX Pages: 2

Brand: EPC Pages: 47

Brand: Cross Technologies Pages: 21

Brand: Felicitysolar Pages: 17

Brand: Grupo Urrea Pages: 8

Brand: Kramer Pages: 12

Brand: Yarvik Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands