manualshive.com logo in svg

Z3 Technology Z3-DME-03, User Instructions, Page: 28 / 54

Share
Download
Z3 Technology Z3-DME-03 User Instructions Download Page 28

 

   

              

            

                                           DOC-USR-0061-03

 

 
 

___________________________________________________________________________________________ 

Z3 Technology, LLC 

♦

 100 N 8

th

 ST, STE 250 

♦

 Lincoln, NE 68508-1369 USA 

♦

 +1.402.323.0702 

28 

6.11

 

 Encoding from HDMI or Composite In 

The Z3-DME-03 also supports encode via HDMI or Composite In. The HDMI or Composite In can be used in 
parallel with the SDI In.  A special cable, provided with the Z3-DME-03, is needed for the Composite In. 
To encode with either HDMI or Composite In, perform the following steps: 

 

 

In the GUI menu, click on the “CH2” tab.  If it is not there, click on “+” to make it appear and then 

click on it: 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   

 
 
 
 
 
 
 
 
 

Figure 33  Clicking on / Creating the CH2 Tab 

If “CH2” not present, 
click on “+” to create it 

Click on “CH2”  
if present 

Summary of Contents for Z3-DME-03























































Reviews:

No comments