Z3 Technology Z3-DME-03 User Instructions Download Page 12 | Manualshive

Page: 12 / 54

background image

DOC-USR-0061-03

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

12

6.3

Find the Z3-DME-03 using ZFinder

Make sure your Windows PC is connected to the same network in which the Z3-DME-03 is connected.

Run the “ZFinder” PC Utility on your Windows PC. The ZFinder window appears. ZFinder does a scan

of the network and lists the location of all Z3 systems connected to the network. In this case, the
Z3-DME-03 appears:

Figure 7 ZFinder with Z3-DME-03 Listed

Click on the Z3-DME-03 entry in the window to select it. This will cause the “Edit Device”, “Open

Device” and “Flash LEDs” boxes to activate:

Figure 8 ZFinder with Z3-DME-03 Selected

Note

:

Since there are no LEDs on the Z3-DME-03, clicking “Flash LEDs” will have no effect.

«
...
10
11
12
13
14
...
»

Summary of Contents for Z3-DME-03























































Reviews:

No comments

Related manuals for Z3-DME-03

Brand: Mitsubishi Pages: 106

Brand: PROEM Pages: 9

Brand: Audio Note Pages: 7

Brand: 3onedata Pages: 3

Allen-Bradley 842D

Brand: Rockwell Automation Pages: 58

Brand: OTS Pages: 14

Brand: IONODES Pages: 23

Brand: opticis Pages: 19

Brand: MRC Pages: 2

Brand: Monoprice Pages: 4

Brand: TSUNESS Pages: 18

Brand: Marshall Electronics Pages: 2

Brand: TR-Electronic Pages: 32

Brand: Invest Solar Pages: 31

Brand: Transition Networks Pages: 5

Brand: Xtreamer Pages: 2

Brand: NovaStar Pages: 9

Brand: Hi-Tech Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands