Z3 Technology FV4K-DCK-1x Hardware Specification Download Page 28 | Manualshive

Page: 28 / 42

background image

28

HE4K-DCK-1x & FV4K-DCK-1x

HARDWARE SPECIFICATION

CONFIDENTIAL

DOC-USR-0100-09

____________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Pin Signal

Pin Signal

1

Composite video output

2

GND

3

GND

4

GPIO3_2 / I2S_MCLK / PWM5

5

GPIO3_1 / I2S_WS_TX / PWM4

6

FLASH_TRIG / GPIO1_0 / SPI2_CSN1 / PWM4

7

UART1_TXD / GPIO5_3

8

GPIO3_3 / I2S_BCLK_TX / PWM6

9

UART1_RXD / GPIO5_1

10 SHUTTER_TRIG / GPIO1_1 / PWM5

11

UART1_RTSn / GPIO5_0 /
UART3_RXD / PWM3

12 USB2_PWREN / GPIO4_5

13 I2C2_SCL / GPIO1_7 (pullup 4.7K)

14 USB_DP

15 I2C2_SDA / GPIO1_6 / (pullup 4.7K)

16 USB_DM

Table 17 Main Encoder Version 2 PCB Digital I/O Connector Pin Out

Table 17 above shows the pin assignments for the CPU board version 2.
Note that pins 13 and 15 have 4.7K pullup resistors to +3.3V on the v2 CPU board.

7.3.7

Analog Audio I/O

This header contains the input and output analog audio signals. It is intended to provide a path for a
differential microphone input and one single ended line level output.

The Analog Audio I/O connector mates with J31 in the I/O Jacks PCB.

Pin Signal

1

GND

2

MIC_BIAS output

3

MIC_IN_P input

4

MIC_IN_N input

5

GND

6

AUD_OUT_L output

Table 18 Main Encoder PCB Audio I/O Connector Pin Out

«
...
26
27
28
29
30
...
»

Summary of Contents for FV4K-DCK-1x











































Reviews:

No comments

Related manuals for FV4K-DCK-1x

Brand: B&B Electronics Pages: 2

Brand: Boss Audio Systems Pages: 5

Brand: Mitsubishi Pages: 12

Brand: Yuan Pages: 15

Brand: Uhlenbrock Elektronik Pages: 4

Brand: AV Access Pages: 20

Brand: Bush Pages: 42

Brand: INVT Pages: 174

SC-TDC-1000 D Series

Brand: Surface Concept Pages: 28

CIS-N-MPPT-LED 85/15

Brand: Phocos Pages: 79

Brand: Black Box Pages: 2

Brand: Brik Pages: 4

Brand: TIE Pages: 4

Brand: Kisae Pages: 12

Brand: Daktronics Pages: 21

Brand: Video Messenger Pages: 25

Brand: Hall Research Technologies Pages: 12

blueplanet 3.0 NX3 M2

Brand: Kaco Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands