Z3 Technology EUS Z3-MVE-150 User Instructions Download Page 77

Page: 77 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

APPENDIX B: Configuring the Wowza Server for RTMP

In this section, configuring Wowza Streaming Engine

version 4.1.0 is described.

To configure Wowza to work with RTMP streaming from your encoder, the following steps are needed:

(1)

http://localhost:8088

, where

“localhost” is the IP address of the server (in this User’s Guide, 192.168.0.4).

(2)

Click on “Server” in the top band of options. On the left column, click on “Performance Tuning” and

then “Java Settings”. Click “Edit” and then change “Java Heap Size” to “Production Level” and
“Java Garbage Collection Settings” to “Concurrent collector”. Click on “Save.”:

All registered trademarks are property of their respective owners.

Figure 69 Wowza Performance Settings

Summary of Contents for EUS Z3-MVE-150
















































































Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands

Z3 Technology EUS Z3-MVE-150, User Instructions

Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands