Z3 Technology EUS Z3-MVE-150 User Instructions Download Page 63 | Manualshive

Page: 63 / 79

background image

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

th

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

63

9.4

MPTS Tab*

An asterisk (

*

) denotes a field available in Advanced Settings Mode. See Section 8.3 to access these

fields.

Parameter

Options (default in bold)

Notes

Rate

*

1-80M (

20M)

The total transport rate of the MPTS stream. This
should equal the bitrates of all channels going into this
stream plus at least a 10% overhead. For example, if
two 10Mbps channels are being packed into the MPTS
stream, the recommended Rate is at least 22Mbps.

Destination 1

*

NONE

ASI

UDP

Used to define where the multiple channels will be
routed to after being combined into one stream. In

most cases, “ASI” is used. Only one destination can be
set to “ASI” at one time.

The MPTS can also be used to send this combined

stream to a UDP URL. If “UDP” is selected,

an IP

Address and IP Port box will appear.

Destination 2

*

NONE

ASI

UDP

An optional second destination for the MPTS streams.

Only one destination can be set to “ASI” at one time.

IP Address

*

(UDP

Destination Only)

IP address that the encoder is streaming to.

IP Port

*

(UDP

Destination Only)

The port that the encoder is streaming to.

«
...
61
62
63
64
65
...
»

Summary of Contents for EUS Z3-MVE-150
















































































Reviews:

No comments

Related manuals for EUS Z3-MVE-150

Brand: Radyne ComStream Pages: 156

Brand: Sungrow Pages: 138

Brand: Transition Networks Pages: 2

Brand: HEIDENHAIN Pages: 6

Brand: UNICOM Pages: 1

Brand: Samlexpower Pages: 2

Brand: e+p Elektrik Handels Pages: 2

AS-07UR4SYDDB15

Brand: Hisense Pages: 59

Brand: Patton electronics Pages: 7

Brand: Sencore Pages: 126

Brand: Goobay Pages: 8

Brand: Parallax Pages: 3

XBMC Clearstream

Brand: Triotech Pages: 16

Brand: Axis Pages: 114

Brand: Black Box Pages: 10

Brand: Acromag Pages: 17

Brand: Ewind Pages: 3

Brand: Fairport Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands