Z3 Technology EUS Z3-MVE-150 User Instructions Download Page 45

Page: 45 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

7.5

Output HDMI

(7)

Connect an HDMI cable from “HDMI Out” on the decoder unit to an HD TV or monitor.

(8)

Return to the user interface System Setup tab. In decoder mode, settings for Display Setup appear.

(9)

Select “hdmi” for the “Display Mode” using the dropdown menu.

(10)

Verify the “Resolution” and “Layout” are as desired and click the “Set Display” button.

Figure 47 Z3-MVE-150 HDMI Output Connection for Decode

HDMI

Out

Figure 48 Set Display for HDMI Output

) Set to “hdmi”

) Click “Set Display”

Summary of Contents for EUS Z3-MVE-150
















































































Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands

Z3 Technology EUS Z3-MVE-150, User Instructions

Search results

Summary of Contents for EUS Z3-MVE-150

Reviews:

Related manuals for EUS Z3-MVE-150

Brands by name

Popular brands