YZ Systems NJEX 7300L, Instructions & Operating Manual, Page: 43 / 126

YZ Systems, Inc. • 3101 Pollok Drive • Conroe, Texas • USA • 77303 • P: 936.788.5593 • F: 936.788.5720
Page 33 NJEX 7300L ver.09042003
SSSSS
ECTION ECTION
ECTION ECTION ECTION
66666::::: P P P P P
R RR
R ROGRAMMING
OGRAMMING
OGRAMMING OGRAMMING OGRAMMING
FOR FOR
FOR FOR FOR
P P P P P
R RR
R ROPOR
OPOR
OPOR OPOR OPORTION
TION
TION TION TIONAL
AL
AL AL AL
-----
TTTTTO O
O O O
-----TTTTT
IME IME
IME IME IME
O O O O O
PERA PERA
PERA PERA PERATION
TION
TION TION TION
Or
SSSSS
ECTION ECTION ECTION ECTION ECTION
66666::::: P P
P P
P
R RR R ROGRAMMING OGRAMMING OGRAMMING OGRAMMING OGRAMMING FOR FOR FOR FOR FOR
P P
P P
P
R RR R ROPOR OPOR OPOR OPOR OPORTION TION TION TION TIONAL AL AL AL AL
-----
TTTTTO O O O O
-----TTTTT
IME IME IME IME IME
O O
O O
O
PERA PERA PERA PERA PERATION TION TION TION TION
*designates optional key function
pmp bat vmtr sig tnk
Set Parameters
*Flow *Time *Esc
pmp bat vmtr sig tnk
Proportional to Time
*Set *Alarm *Esc
pmp bat vmtr sig tnk
Odorant Density
6.80 lbs/Gal pmp bat vmtr sig tnk
Odorant Density
0.815 g/cc
pmp bat vmtr sig tnk
Set Selection
*Par *Cal *Esc
pmp bat vmtr sig tnk
PropFlow Idle
*Strt *Dsp *Set
pmp bat vmtr sig tnk
Pump Displacement
1.000 cc/Stroke
Select
Enter
Select
Enter
Select
Enter
Figure 53
Figure 54
Figure 55
Figure 56
Figure 57
Figure 58
Figure 59
Setting Operator Input Parameters
Choose Set from the main menu, figure 53.
Choose Par from the set selection menu, figure 54.
Choose Time from the set parameters menu, figure 55.
Choose Set from the proportional-to-time menu, figure 56.
Pump displacement in cc/stroke
To set the pump displacement, figure 57, press and
release the Select key. The value entry will begin to
flash when chosen. Use the Up Arrow key to increase
the value and the Down Arrow key to decrease the
value. When a new value has been chosen, press the
Enter key to store the new value into memory. The
entered value will stop flashing when it has been loaded
into memory. Press the Down Arrow key to advance to
the next parameter.
Odorant density in lbs/gallon (g/cc.) @ 60ºF
To set the odorant density, figure 58, press and
release the Select key. The value entry will begin to
flash when selected. Use the Up Arrow key to
increase the value and the Down Arrow key to
decrease the value. When a new value has been
chosen, press the Enter key to store the new value
into memory. The entered value will stop flashing
when it has been loaded into memory. Press the
Down Arrow key to advance to the next parameter.
Time interval between strokes of the pump in
xx.xx minutes/stroke:
1. 0.00 minutes = proportional-to-time disabled.
2. 0.02 to 99.99 minutes = proportional-to-time
enabled.
To set the time/strokes, figure 59, press and release
the Select key. The value entry will begin to flash
when chosen. Use the Up Arrow key to increase the
value and the Down Arrow key to decrease the
value.
pmp bat vmtr sig tnk
Set Time Per Stroke
0.50 minutes