background image

ST16 USER MANUAL

INTRODUCTION

The ST16 is equipped with a touchscreen display that allows for changing 

various settings and viewing real-time telemetry data and streaming video during

flight. The ST16 seamlessly integrates control of the camera so you can easily

take still photos and start/stop video recording using the corresponding

buttons.

OPERATING INSTRUCTIONS:

ST16 AND RECEIVER BINDING
STEP 1): Powe

r on the ST16 and tap “RC” on the main interface

STEP 2): Tap Model Select and if required press “OK” to bypass any pop up warning/alerts. 

STEP  3):  Tap  to  create  a  new  model  and  if  required  press  “OK”  to  bypass  any  pop  up  warn-

ings/alerts.

STEP 4): Tap Flight Settings and if required press “OK” to bypass any pop up warnings/alerts.

STEP 5): Lift the H920 back end upward approximately 45° , then back down to “level” twice till the 

main LED indicator blinks yellow.

STEP 6): Tap the Refresh icon. Select the code of the H920 listed in the column under ”Model” and 

tap Bind ,then tap “OK”  after the connection has been established

STEP 7): When tapping, you will hear two long beeps from the aircraft. That means the ST16 is 

bound to the H920 successfully.

STEP 8): Tap [         ] twice to return to the main screen and the model /receiver should automatically 

connect to ST16

NOTICE: The H920 main LED indicator will blink red and white if the TORNADO loses GPS signal 

/lock. The H920 main LED indicator will be solid color of the current mode if the GPS signal/lock is 

acquired.

tions, may cause harmful interference to radio communications. However, there is no guarantee 

that interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the following 

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

—Consult the dealer or an experienced radio/TV technician for help.

RF EXPOSURE WARNING

• This equipment must be installed and operated in accordance with provided instructions and the 

antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 

cm from all persons and must not be co-located or operating in conjunction with any other antenna 

or transmitter. End-users and installers must be provide with antenna installation instructions and 

transmitter operating conditions for satisfying RF exposure compliance.

IC RADIATION EXPOSURE STATEMENT FOR CANADA

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may cause undesired opera-

tion of the device.

Le  présent  appareil  est  conforme  aux  CNR  d'Industrie  Canada  applicables  aux  appareils  radio 

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit 

pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélec-

trique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
This equipment complies  with IC RSS-102 radiation exposure limit set forth for an uncontrolled 

environment.

Cet équipement respecte les limites d'exposition aux rayonnements IC définies pour un environne-

ment non contrôlé

 

Summary of Contents for ST16

Page 1: ...warn ings alerts STEP 4 Tap Flight Settings and if required press OK to bypass any pop up warnings alerts STEP 5 Lift the H920 back end upward approximately 45 then back down to level twice till the main LED indicator blinks yellow STEP 6 Tap the Refresh icon Select the code of the H920 listed in the column under Model and tap Bind then tap OK after the connection has been established STEP 7 When ...

Page 2: ...ted States TAKING PHOTOS AND RECORDING VIDEO TO TAKE A STILL PHOTO Press the button located near the top left corner of the ST16 You ll hear an audible shutter sound from the ST16 and the LED indicator on the front of the camera will change from glowing solid green to glowing solid blue It will take approximately 1 2 seconds to capture the photo and before you can take another still photo TO START...

Page 3: ...the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must acc...

Page 4: ...intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonnée équivalente p i r e ne dépasse pas l intensité nécessaire à l établissement d une communication satisfaisante User manuals for transmitters equipped with detachable antennas shall also contain the following notice in a conspicuous location This radio transmitter identify the ...

Reviews: