background image

Page 1 of 4

 A division of Terry Young Ltd , New Zealand

 INSTALLATION INSTRUCTIONS for

FITZROY FREESTANDING WOODBURNER

APRIL 2007

TESTED in compliance with AS/NZS 2918: 2001

A

. Yunca recommends that competent trades persons carry out all installations (e.g. NZHHA

Registered Installer), to obtain maximum performance and safe, efficient heating.

B

. A permit is required and we suggest you check with local building inspectors as by-laws do

vary from area to area.

Also notify your Insurance Company that a solid fuel heater has been installed.

C

. Floor Protector –

1.  Must extend a minimum of 300mm in front of the door aperture.

2.  Must extend at least 100mm from each side of the heater.

3.  Ash Floor Protector must be constructed of non-combustible materials, with a

minimum thickness of 12mm

D

. Seismic restraint – Heater must be restrained from seismic movement as required by  NZS

7421. 10mm diameter bolting holes in the feet of the HOBSON allow restraint.

E.

 Manufacturers’ recommended tested minimum clearances from combustible walls:

Tested to AS/NZS 2918 : 2001 by APPLIED RESEARCH SERVICES

Clearance

Rear Clearance  – from rear of top lip 

(with YUNCA flue mounted shield fitted)

                                - N.B. clearance from rear panel is 120mm

100 mm

Side Clearance (with YUNCA flue mounted shield fitted)

300 mm

Corner Clearance (with YUNCA flue mounted shield fitted)

130 mm

F. YUNCA Flue Kit (Tested to AS/NZS 2918:2001 Appendix F): Fig A, B & E

1

. 4.2m x 150mm stainless steel flue

4

. 1 x insulation boundary shield.

2

. 2.4m x 250mm galvanised liner.

5. 

3 x spider brackets.

3.

 1 x ceiling tile.

6. 

1 x weather cap & cowl.

Please Note: 

All joints must be sealed with flue sealing compound. Use stainless steel

screws or rivets to join the flue pipe (three equally spaced places at each joint). The first

length of flue pipe must be screwed to flue spigot. The required minimum flue termination

height is 4.6 m above the floor protector.

G. FITZROY Flue Mounted Shield (Flue Guard) Kit (Tested to AS/NZS 2918:2001): Fig A

1 x 1200mm length lined back guard plus an adjustable 900mm extension.

1 x 1200mm length perforated front guard

1 x 1200mm length tertiary back guard with spacer tabs.

1 x Top front deflector shield (half round shape, angled when installed). Optional.

Please Note: The minimum Flue Mounted Shield height Is 1200mm. 

Extension accessory

shields are also available.

Summary of Contents for FITZROY

Page 1: ...PPLIED RESEARCH SERVICES Clearance Rear Clearance from rear of top lip with YUNCA flue mounted shield fitted N B clearance from rear panel is 120mm 100 mm Side Clearance with YUNCA flue mounted shield fitted 300 mm Corner Clearance with YUNCA flue mounted shield fitted 130 mm F YUNCA Flue Kit Tested to AS NZS 2918 2001 Appendix F Fig A B E 1 4 2m x 150mm stainless steel flue 4 1 x insulation bound...

Page 2: ... within 3 0m In any case the length of the flue shall not be less than 4 6m from the ash floor protector In some situations the Local Council may vary the above requirements 2 All parts of the chimney exposed to the outside air shall be suitably insulated in accordance with the manufacturers recommendations When loose fill insulation is used in the adjacent ceiling space maintain clearance between...

Page 3: ...ED Measurements in millimetres A B E F G H 100 300 130 325 620 501 FIG D MINIMUM FLOOR PROTECTION MEASUREMENTS WITH YUNCA FLUE MOUNTED SHIELD FITTED Measurements in millimetres C D J K L M N O P 300 100 840 910 1274 1150 575 640 610 Above Non combustible wall clearances Brick lining from floor to within 25mm of ceiling Leave air vents at the bottom to allow airflow in the cavity If Yunca flue moun...

Page 4: ...NZS 4013 C Any modification of the appliance that has not been approved in writing by the testing authority is considered to be in breach of the approval granted for compliance with AS NZS 4013 D Mixing of appliance or flue system components from different sources or modifying the dimensional specification of components may result in hazardous conditions Where such action is considered the manufac...

Reviews: