YSI 2900 series Operation And Maintenance Manual Download Page 90

Page: 90 / 166

7.2.5 Monitor

From the Service menu, touch the [Monitor] tab.

Test Outputs

Touch the DAC A or DAC B [0.00V] button to test the analog output by setting the output to 0, 5 or 10VDC.

Touch the Ready, Feed Pump, Filtrate Pump, or SysErr [Off] button and change it to [On] to test the corresponding output.

Valve

Touch the Opened Valve [Antiseptic] button to change the state of the valve and change it to [Sample]

Prime Monitor Pump

Touch the Pump Sample [Off] button and change it to [On] to prime the monitor sample line. The pump will turn off
automatically.

If you are using an antiseptic solution, touch the Pump Antiseptic [Off] button and change it to [On] to prime the antiseptic
solution. The pump will turn off automatically.

NOTE: After sterilization, the antiseptic solution must be primed immediately after the tubing is reconnected.

Summary of Contents for 2900 series







































































































































































Search results

Summary of Contents for 2900 series

Reviews:

Brands by name

Popular brands

YSI 2900 series, Operation And Maintenance Manual

Search results

Summary of Contents for 2900 series

Reviews:

Brands by name

Popular brands