manualshive.com logo in svg

YSI 2900 series, Operation And Maintenance Manual

Share
Download
YSI 2900 series Operation And Maintenance Manual Download Page 86

85 

 

Touch 

 at the bottom right of the adjustment window, then touch 

 to confirm saving the position. 

7.2.2  Pumps 

From the Service menu, touch the [Pumps] tab.  

 

7.2.2.1  Sipper Pump 

Home 

Touch the [Home] button to Home the sipper pump plunger. The pump plunger will extend fully, then retract slightly. 

Aspirate 

Touch the [Aspirate] button. The pump plunger will retract about half way as it does when it aspirates a sample. Note that 
the actual distance depends on the sample size setting. 

Dispense 

Touch the [Dispense] button. The pump plunger will extend about half way as it does when it dispenses a sample into the 
sample module. 

When you have finished testing the sipper pump, touch the [X] button to return to the main display. 

7.2.2.2  Buffer Pumps 

Touch the [ON] button under a buffer pump. The selected buffer pump will run. Touch the [OFF] button to stop the pump. 

When you have finished testing the buffer pumps, touch the [X] button to return to the main display. 

7.2.2.3  Calibrator Pumps 

Touch the [ON] button under a Cal Pump. The selected calibrator pump will run. Touch the [OFF] button under the same 
pump to stop it. 

NOTE: Prime all installed calibrator bottles daily to remove air bubbles from the tubing.

 

When you have finished testing the fluid pumps, touch the [X] button to return to the Main display. 

Summary of Contents for 2900 series







































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands