YSI 2900 series Operation And Maintenance Manual Download Page 83

Page: 83 / 166

Service

7.2

Touch [Service] to display the Service menu.

7.2.1 Sipper

for details on aligning the sipper with each sample module.

If necessary, the sipper can also be aligned with Station 2, the different types of racks/plates used at Station 1, and the
calibrator wells.

NOTE: If 21 CFR Part 11 mode is enabled, only an Administrator can access the Sipper tab.

7.2.1.1 Interlock

Touch the Interlock button and change the status to [Off] to disable the interlock switches on the front door and side panel
when aligning the sipper.

WARNING: Keep your hands clear of the sipper while the instrument is in operation.

Always turn the Interlock back [On] before operating the instrument!

Service

Summary of Contents for 2900 series







































































































































































Search results

Summary of Contents for 2900 series

Reviews:

Brands by name

Popular brands

YSI 2900 series, Operation And Maintenance Manual

Search results

Summary of Contents for 2900 series

Reviews:

Brands by name

Popular brands