Yoshitake TRAP STAR TSF-8 Product Manual Download Page 1

 

 

■EPDT-320b■

 

 

 
 
 
 

PRODUCT MANUAL

 

.

 

Thank  you  very  much  for  choosing  the  Yoshitake’s  product.    To  ensure  the  correct  and  safe  use  of  the 

product, please read this manual before use.    This manual shall be kept with care for future references. 
The symbols used in this manual have the following meanings. 

 

          Warning 

This  symbol  indicates  a  potentially  hazardous  situation  that,  if  not  avoided, 
could result in death or serious injury. 

          Caution 

This symbol indicates a hazardous situation that, if not avoided, may result in 
minor or moderate injury or may result in only property damage. 

 

 

Table of Contents 

 

1. Usage of the Product ·················································· 1 

2. Specifications ···························································· 1 

3. Dimensions and Weights ············································· 2 

4.

 

Operation   ······························································· 3 

5. Maximum Continuous Discharge Capacity ······················ 4 

6. Installation   

6.1 Piping example ···················································· 5 

6.2 Precaution for installation ······································· 7 

7. Operating Procedure ················································· 10 

7.1 Precaution for operating procedure ························· 10 

8. Maintenance 

8.1 Precaution for maintenance ·································· 10 

8.2 Daily and periodic inspections ······························· 11 

8.3 Troubleshooting ·················································· 12 

8.4 Exploded drawing ··············································· 13 

8.5 Disassembly ······················································ 14 

8.6 Reassembly ······················································· 15 

8.7 Parts replacement procedure ································ 16 

Warranty Information 

 

 

 

 

STEAM TRAP 

MODEL TSF-8,8F 

Summary of Contents for TRAP STAR TSF-8



















Reviews: