YORKVILLE M1610 Owner'S Manual Download Page 8

   

6

Digital Effects Processor

1. Select and MODIFY EFX Controls

Use the 

EFX Selection

 control to choose from the sixteen 24-bit digital reverbs, delays 

and other effects. This control ro-tates continuously, which lets you rotate clockwise or 

counter-clockwise to select the desired effect. For convenience, a table of the effects and 

their variables appear later in this manual and on the front panel of the 

M810/M1610

Parameters for each of the effects can be changed using the 

MODIFY

 control which is 

located next to the 

Selection

 control. For example, if a Hall reverb has been selected, 

the 

MODIFY

 control will let you adjust the decay parameter. Choosing the Chorus effect 

allows the chorus rate to be adjusted. 

Note: The signal sent from the internal Digital Effects Processor to the MON mix is 

independent from the MON send controls on the channel strips. When a channel’s 

EFX control routes a signal to the internal Effects processor and the MON level con-

trol (for that channel) is turned off, the channel’s wet effects will still be audiable in 

the monitor bus (if the EFX to MONitor return level is turned up).

2. Effects CLIP LED

Situated to the right of the 

MODIFY EFX

 control, the 

CLIP LED

 indicates that the digi-

tal processor is receiving an input signal that’s too strong, resulting in distortion. For 

optimum performance, the 

CLIP LED

 should never flash. If there is clipping activity, turn 

down the channel 

EFX

 controls appropriately.

Built in 9-Band Graphic Equalizer & Shelving EQs

1. General

Each EQ consists of a set of +/-15dB range type controls. In the 

M810/M1610

 there are 

nine sliders for each channel, each one operating over a 2/3-octave portion of the mid-

range band of sound frequencies, as well as 

rotary

 shelving Bass and Treble controls. 

Note:

 Equalizers have an effect on the gain of the main system as well as its fre-

quency response. Once adjusted, you may need to adjust the MAIN master level if 

the clip LEDs become too active.

M810/M1610

Series 2

Room Reverb

Hall Reverb

Hall Reverb - Vocals

Hall Reverb w/Echo

Plate Reverb

Plate Reverb - Vocals

Plate Reverb w/Echo

Gated Reverb

decay

decay

decay

decay

Modify

Effect

decay

gain

pitch

delay

rate

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

15.

16.

Fast Echo 

Short Decay Echo

Long Decay Echo

Chorus

Flanger

Rotary Speaker

Distortion

Harmonizer

Modify

Effect

24

E Q U A L I Z E R   A

E Q U A L I Z E R   B

+15

+10

+5

0

-5

-10

-15

+15

+10

+5

0

-5

-10

-15

160 250 400 630 1.0K 1.6K 2.5K 4.0K 6.3K

160 250 400 630 1.0K 1.6K 2.5K 4.0K 6.3K

-15

+15

-15

+15

-15

+15

-15

+15

Lo

Hi

Lo

Hi

Summary of Contents for M1610































Reviews: