Ref:.. \operat98\instructions 19\28229.qxp 17-01-19
©York Survey Supply Centre 2019
Code: 28229
Operating
Instructions
Explorer Premium
Video Borescope
2. Press the
p
or
q
button to select ‘Frame Rate’ and then press the ‘OK’ button.
3. Press the
p
or
q
button to toggle between different frame rates. Once you have
highlighted your desired selection, press the ‘OK’ button to confirm and exit.
Time Stamp Setting
1. In the setting mode, press the
p
or
q
button to select ‘RECORDER SETTING’
and then press ‘OK’ button.
2. Press the
p
or
q
button to select ‘Time Stamp’ and then press the ‘OK’ button.
3. Press the
p
or
q
button to toggle between on and off. Once your desired selection
is made, press the ‘OK’ button to confirm and exit.
Recording Type
1. In the setting mode, press the
p
or
q
button to select ‘RECORDER SETTING’
and then press ‘OK’ button.
2. Press the
p
or
q
button to select ‘Recording Type’ and then press the ‘OK’ button.
3. Press the
p
or
q
button to toggle between ‘still’ and ‘video’. Once your desired
selection is made, press the ‘OK’ button to confirm and exit.
Event Playback
1. In the setting mode, press the
p
or
q
button to select ‘EVENT PLAYBACK’ and
then press ‘OK’ button.
2. Refer to the user manual instructions on Playback of Video/Picture, Deleting
Video/Picture and Deleting Folder for guidance.
TROUBLESHOOTING
SPECIFICATIONS
Actual transmission range of wireless monitoring may vary according to the weather,
location, interference or building construction.
All specifications are subject to minor change without notice.
FCC INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation. Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
The graphics included in this user manual are subject to minor change without notice.
c
a
m
e
r
a
Imaging Sensor
CMOS
Total Pixels
640 x 480 (PAL)
640 x 480 (NTSC)
Horizontal Viewing Angle
36°
Transmission Frequency
2468MHz
Minimum Illumination
0 Lux
Modulation Type
FM
Bandwidth
18MHz
Power Supply
4x AA batteries
Unobstructed Effective Range
10m (max)
Waterproof Capacity
IP67 (for lens/tube only)
Tube Diameter
9mm
Dimensions (WxDxH)
186 x 145 x 41mm (excluding flexible tube)
Approx. Weight
408g
m
o
n
i
t
o
r
LCD Screen Type
3.5” TFT-LCD
Effective Pixels
960 x 240
Video System
PAL/NTSC
Transmission Frequency
2414MHz, 2432MHz, 2450MHz, 2468MHz
Exterior Supply Voltage
5VDC
Consumption Current (Max.)
500mA
Charging Time
3 hours
Working Time
2 hours
Picture/Video Pixels
640 x 480
Video Size
20M byte/minute
Frame Rate
30 frame/second
Video Output Level
0.9-1.3VP-P@75ohm
Receiving Sensitivity
<-85dBm
Dimensions (WxDxH)
100 x 70 x 25mm
Approx. Weight
140g
Operating Temperature
-10°C to +40°C / +14°F to +104°F
Operating Humidity (Max.)
15 to 85%RH
Problem
Possible Cause
Likely Solutions
Tool will not start 1. Monitor not charged
2. Batteries need charging
1. Charge monitor
2. Replace batteries in control
handle
Monitor will not
charge
1. Adaptor cable not attached
properly
2. Adaptor not connected to
power
1. Make sure adaptor cable is
connected between monitor
and adaptor
2. Make sure adaptor is
securely plugged into wall
socket
Image too dark
or light
1. LEDs near camera need
adjustment
2. Monitor display needs
adjustment
1. Use dial on control handle to
adjust brightness of LEDs
2. Use contrast and brightness
buttons on monitor to adjust
image
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Prospect House, George Cayley Drive, Clifton Moor, York, England YO30 4XE
Tel: +44 (0) 1904 692723 Fax: +44 (0) 1904 690385
E-Mail: [email protected] www.yorksurvey.co.uk
York Survey Supply Centre
Follow us!
@York_Survey
@York_Survey
