YOKOGAWA WT1800E User Manual Download Page 128

Page: 128 / 154

20-3

IM WT18O1E-02EN

20.2 Configuring TCP/IP Settings

This section explains the following TCP/IP settings for connecting this instrument to a network:
•  DHCP
  IP address, subnet mask, and default gateway
•  DNS
  Domain name, DNS server IP address, and domain suffix

►

“TCP/IP (TCP/IP)” in the features guide

Configuring TCP/IP Settings (TCP/IP)

Press

UTILITY

, the

Network

soft key, and then the

TCP/IP

soft key to display the following screen.

Set the DHCP (OFF, ON).

Set these when DHCP is set to OFF.

• IP address

• Subnet mask

• Default gateway

These are displayed when DNS is set to ON or Auto.

• Domain name

• DNS server IP address

(1: primary, 2: secondary)

• Domain suffix

(1: primary, 2: secondary)
Applies the settings

Set the DNS (OFF, ON, Auto).

• OFF: The DNS is disabled.

• ON:

The DNS is enabled. Set the domain name, and the DNS server’s primary and

secondary IP addresses and domain suffixes.

• Auto: The DNS is enabled. Set the domain suffixes. The domain name and the DNS server

IP addresses are set automatically. The Auto option is only displayed when DHCP is

set to ON.

Summary of Contents for WT1800E



























































































































































Search results

Summary of Contents for WT1800E

Reviews:

YOKOGAWA WT1800E, User Manual, Page: 128 / 154

Search results

Summary of Contents for WT1800E

Reviews: