manualshive.com logo in svg

YOKOGAWA TB830D, User Manual, Page: 43 / 85

Share
Download
YOKOGAWA TB830D User Manual Download Page 43

< 4. SETTING PARAMETERS >

4-8

IM 12E04B40-02EN

1st Edition : Mar. 08, 2023-00

4.5.4 

Auto sequence setting

Configure the following parameters to setup the schedule for Automatic cleaning and Automatic 

zero calibration.

•  Cleaning interval
•  Repeat count of wash
•  Calibration frequency

The auto-sequence starts at the setup hour of the start time at the washing interval cycle.
See how many times the automatic cleaning repeats in a sequence by setting “Repeat count of 

wash”. When Auto calibration function” is ON, Auto sequence starts at an interval determined 

calibration frequency. When automatic cleaning ends, automatic zero calibration operates one 

time. When Calibration frequency is set to “0”, no Auto calibration operates.

The next figure shows the example when. Repeat count of wash is 2. Calibration frequency is 3.

Start date and time

Next sequence start

Next sequence start

Time schedule

Washing interval

Number of washes

Washing interval

Number of washes

Washing interval

Number of washes

Wash Wash

Wash Wash

Wash Wash

Cal

Wash

Wash

Automatic calibration takes place one time after the auto sequence repeats as many calibration frequencies.

Other parameters are for setting details about one count of automatic cleaning/automatic zero 

calibration. For further information on the auto sequence, read “Appendix  Automatic cleaning/

Automatic zero calibration Sequence”.

CAUTION

The settings changed in the wash interval will be reflected in the second “start date and time” that 

follows.

Summary of Contents for TB830D






















































































Reviews:

No comments