manualshive.com logo in svg

YOKOGAWA TB830D, User Manual, Page: 17 / 85

Share
Download
YOKOGAWA TB830D User Manual Download Page 17

<2.  INSTALLATION, PIPING, AND WIRING>

2-4

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

*1:  Option /L (Air denoising for Low Range)
*2:  You should install a check valve before the tap water pipe to prevent backflow. 

Head tank

Manual valveV1

Pinch

valve

SV4

Manual

valve V2

Manual valve

V3

Zero turbidity filter

Sample (VP16)

Tap water (VP16) *2

Drain (VP40)

PVC tray

*1

Detector

Manual valve

V4

Solenoid valve

SV2

Figure 2.2 

-A2 With sampling system (with auto cleaning, without auto zero calibration)

Head tank

Manual valveV1

Manual valve

V4

Pinch 

valve SV4

Solenoid valve

SV2

Solenoid

valve SV3

Solenoid valve

SV1

Manual

valve V2

Manual

valve V3

Zero turbidity filter

Sample (VP16)

Tap water (VP16) 2*

Drain (VP40)

PVC tray

1*

Detector

1*:  Option /L (Air denoising for Low Range)

M

2*:  You should install a check valve just before the tap water pipe to prevent backflow 

Figure 2.3 

 -A3 With sampling system (with auto cleaning, with auto zero calibration)

(1)  Sample piping

 

This piping is used to feed the sample to the detector.

 

The pressure condition of the sample is 20 to 500 kPa, and the flow rate is 2 to 10 L/min .

 

The pipe joints are rigid PVC pipes with a nominal diameter VP16 (O.D. ø22mm). Before 

piping, install any fittings that match the pipe diameter, such as unions or flanges.

Summary of Contents for TB830D






















































































Reviews:

No comments