YOKOGAWA TA720 User Manual Download Page 129

Page: 129 / 228

9-9

IM 704510-01E

Statistical Calculation and Inter-Symbol Interference Analysis

Explanation

Selecting the Display Style

By turning OFF Overlap, the histogram of the extracted data and that of all spaces or

marks can be displayed separately.

Turning ON/OFF the Sync Function

Select ON to start analyzing from the searched pattern using the symbol search function

or OFF to analyze the all the measured values. For the setup procedure of the symbol

search function, see section 8.6, “Symbol Search”.

Statistical Parameters That Are Listed

The statistics of all marks (spaces) and extracted data and the number of samples are

listed for each window. The statistical calculation parameters are set using the

Calculation/Statistics Setting dialog box (see page 9-6). However, only the top two

parameters are displayed.

Selecting the Extraction Mode

Select from the following.

• Single:

Activates the trigger on a Space or Mark and analyzes the data around

the trigger.

• Combination: Uses the sequence of a space followed by a mark or a mark followed

by a space as a trigger and analyzes the data around it.

• Between:

Uses a mark or a space existing between two spaces or two marks as

a trigger and analyzes the data between them.

Selecting the Polarity of Mark/Space

Select whether spaces will be positive (+) or marks will be positive (+).

Selecting the Trigger/Selecting the Data to Be Extracted

You can select which mark or space will be used as a trigger. The types of trigger that

can be selected vary depending on the extraction mode.

The data around or between triggers can be extracted, but the data that can be extracted

vary depending on the extraction mode as shown below. In the table below,

represents a space and

represents a mark. On the TA720, you can select which

window will be marks and which will be spaces.

• Pulse width measurement or pulse width A

→

pulse width B measurement.

Mode

Trigger

Target

Explanation

Single

Prev.

/Next

/Both

Extracts the data immediately before or

Prev.

/Next

/Both

after the trigger or both

Combination

Prev.

/Next

Extracts the data immediately before or

Prev.

/Next

after the trigger

Between

–

Extracts the data between two spaces

–

Extracts the data between two marks

9.2 Setting the Inter-symbol Interference Analysis

Summary of Contents for TA720





































































































































































































































Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands

YOKOGAWA TA720, User Manual

Search results

Summary of Contents for TA720

Reviews:

Related manuals for TA720

Brands by name

Popular brands