manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 95

4-7

IM DL950-02EN

4.4  Triggering on an Time Trigger (Simple) in 

Scope Mode

This section explains the settings that are used when triggering on a specific date and time in 
Scope mode.

Applicable in Scope Mode

•  Trigger source
•  Date and time
•  Time interval

► “Simple Trigger (Simple)” and “Trigger Source (Source)” in the Features Guide

Trigger Menu

1.

  On the waveform screen’s 

MENU

, tap 

TRIGGER 

> 

MENU

, or press 

TRIG.MENU

. A trigger 

menu appears.

  

Select Simple.

Set the trigger source to Time.

See “Setting the Date and Time.”

Set the time interval.

Set the trigger position, trigger delay, and hold-off 

► sec. 4.2

Set the trigger mode. ► sec. 4.1

Setting the Date and Time (Date/Time Setting)

2.

  Press the 

Date/Time

 soft key. The following screen appears.

  

Set the date and time.

Confirms the date and time

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands