YOKOGAWA ScopeCorder DL950 User Manual Download Page 59

Page: 59 / 316

2-43

IM DL950-02EN

Configuring LIN Frame Reading Settings (LIN Port Configuration)

Tap

LIN Port Configuration

, or press the soft key.

All Sub Channel Setup (All SubChannel Setup - LIN Data Extraction

Conditions)

Tap

All SubChannel Setup

, or press the soft key. The following screen appears.

See “Frame Setup.”

LIN data extraction conditions

Turns sub channels on or off

Set each sub channel’s input to on or off.

See “Port Setup.”

See “Setting All Sub

Channel

Factor/Offset.”

Turns all sub channel on or off

See “Loading

Definition Files.”

Setting All Sub Channel Factor/Offset (All SubChannel Factor/Offset - LIN

Data Conversion Condition)

Tap

All SubChannel Factor/Offset

, or press the soft key. The following screen appears.

LIN data conversion conditions

You cannot set Factor, Offset, or Unit when the data type (Value

Type) is set to Logic.

2.10 Configuring the Monitoring of LIN Bus Signals (/VCE option)

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Brands by name

Popular brands

YOKOGAWA ScopeCorder DL950, User Manual

Search results

Summary of Contents for ScopeCorder DL950

Reviews:

Brands by name

Popular brands