manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 308

23-9

IM DL950-02EN

23.6  Configuring the Environment Settings

This section explains the following instrument settings:

Items Common to Scope Mode and Recorder Mode

•  Power-on action
•  Logic
•  External I/O terminal
•  Click sound on/off and key lock type and release method
•  Beep on errors, backup when the power is turned off
•  Turning the touch panel feature on and off

► “Environment Settings (Preference)” in the Features Guide

UTILITY Preference Menu (Preference)

1.

  On the waveform screen’s MENU, tap 

OTHERS

 > 

UTILITY

, or press 

UTILITY

.

2.

 Tap 

Preference

, or press the soft key. The following screen appears.

  

Select Preference.

See “Configuring the Logic Settings.”

See “Setting the Action to Perform 

at Power On.”

See “Turning the Click Sound On and Off 

and Configuring the Key Lock Settings.”

See “Configuring the External I/O 

Terminal Settings.”

See “Setting the Beep Sound.”

Turns the touch panel feature on or off.

Setting the Action to Perform at Power On (Power On Action)

3.

 Tap 

Power On Action

, or press the soft key. The following screen appears.

  

Select whether to start waveform acquisition 

at power on.

Select whether to enable the previous action’s settings 

at power on.

Set how the instrument is to behave when the main 

power switch on the side panel is turned on.

Startup Mode

Set how the instrument is to behave when the main power switch on this instrument’s side 
panel is turned on.
 

Standby Startup: 

Stand by until the power switch on the front panel is turned on.

 

Immediate Startup:  Start the instrument.

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands