manualshive.com logo in svg

YOKOGAWA ScopeCorder DL950, User Manual

Share
Download
YOKOGAWA ScopeCorder DL950 User Manual Download Page 307

23-8

IM DL950-02EN

23.5  Using the Instrument as a USB Storage Device

This section explains the setting that enables you to use the instrument as a USB storage device 
through a USB connection made between the USB port on the instrument’s side panel and a PC.

Items Common to Scope Mode and Recorder Mode

•  Setting the USB function

► “Remote Control (Remote Ctrl)” in the Features Guide

UTILITY Remote Ctrl Menu

1.

  On the waveform screen’s MENU, tap 

OTHERS

 > 

UTILITY

, or press 

UTILITY

.

2.

 Tap 

Remote Ctrl

, or press the soft key. The following screen appears.

  

Select Remote Ctrl.

Set USB Function to Storage.

Set Device to USB.

Note

•  When USB Function is set to Storage, only this instrument’s internal SSD can be used as a storage 

device. You cannot access any other storage device that are connected to the instrument.

•  When you access this instrument’s internal SSD from a PC, only perform read and write operations. 

Otherwise, the instrument may be damaged.

•  When USB Function is set to Storage and files are being accessed, do not remove the USB cable or turn 

off the instrument. Otherwise, the instrument may be damaged.

•  When USB Function is set to Storage, do not access this instrument’s internal SSD from the instrument’s 

menu.

•  When you set USB Function to TMC, you can control this instrument from a PC via USB. For details, see 

the 

Communication Interface User’s Manual

, IM DL950-17EN, contained in the CD.

Summary of Contents for ScopeCorder DL950





























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands